background image

 

83 

Chapter 21.

 

 

LAG Configuration 

Introduction 

This chapter describes configuration of uplink interfaces aggregation. Link aggregation (IEEE 802.3ad) is a 

technology  that  allows  multiple  physical  links  to  be  combined  into  one  logical  link  (aggregation  group).  
Aggregation group has a higher throughput and is very reliable. 

 

 

Fig. 21.1 – Multiple Physical Links Combined to an Aggregation Group 

 

The  terminal supports  two  interface  aggregation modes:  static and  dynamic.  Static  aggregation  implies 

that  all  communication  links  of  a  group  are  always  active.  As  for  dynamic  aggregation,  link  activity  is 
dynamically determined during operation via LACP protocol. 

Table 21.1 – Operation Modes of Aggregation Groups 

Mode 

Description 

static 

Link aggregation protocol is not used 

lacp 

LACP is used 

The terminal has several algorithms of load balancing within aggregation groups. 

Table 21.2 – Load Balancing Modes 

Mode 

Description 

ip 

Based on IP addresses of sender and receiver 

ip-l4 

Based on IP addresses of sender and receiver, and L4 

mac 

Based on MAC addresses of sender and receiver 

mac-ip 

Based on MAC and IP addresses of sender and receiver 

mac-ip-l4 

Based on MAC and IP addresses and L4 of sender and receiver 

 

Summary of Contents for LTP-4X








































































































































































































Reviews: