background image

_________________________________________________________________________________ 

 _________________________________________________________________________________ 

Universal Network Terminal TAU-32M.IP                                                                 165

 

5.1.5

 

The 'System info' menu 

5.1.5.1

 

The 'Device info' submenu 

In the 

'System info'

 menu, you can view the system information. 

 

 

System  time

  –  device  system  date  and  time  in  the  following  format:  hours:minutes:seconds 

day/month/year; 

 

Uptime

 – time of the uninterrupted gateway operation; 

 

TAU-32M.IP

 – firmware version; 

 

Software Version – 

device firmware version. 

Device information 

 

Linux version–

Linux OS version; 

 

Firmware version

 – media processor firmware version; 

 

BPU version

 – hardware version; 

 

Factory type, SN, MAC–

factory settings; 

 

User  MAC

  –  МАС  address,  defined  by  user.  In  this  case,  factory  МАС  address  will  be  ignored.  You  can 

specify МАС address from the CLI console only; 

 

Board id – 

hardware platform version;

 

 

Power supply

 – type of power supply installed (AC or DC). 

Summary of Contents for TAU-32M.IP















































































































































































































































































































































Reviews: