background image

____________________________________________________________________________________ 

____________________________________________________________________________________ 

44  

 

VoIP subscriber gateways

 

 

Enterprise.3.1 – system log settings. 

Where Enterprise – 1.3.6.1.4.1.35265.1.55 is the TAU-8.IP device identifier. 

To save  changes  into  the device operative  memory, click  ‘

Save  Changes

 

button.  To  record  settings  into 

the non-volatile memory, click ‘

Apply

 

button

.

 

3.1.3

 

Print Server

 menu 

Use the ‘

Print server

 

menu to configure the print server. 

 

 

Enable print server

 – when checked, print server is enabled.

 

When  the  printer  is  connected  to  the  USB  port,  it  should  be  determined  automatically.  To  configure 

printer, specify gateway path to the ppd file with detailed information about printer functionality. You may find 
this ppd file in the web site of printer vendor.  

Printer configuration in Windows: 

The following steps are required to configure printer in Windows: 

1.

 

Go  to  ‘

Start  menu 

  Printers  and 

faxes’

  and  select 

‘Installation

  of  new  printer 

  Network 

printer or printer connected to another PC

 

 

Connect to a printer via Internet, home network 

or intranet

 and enter string with 

URL

http://server:631/printers/model

.  

 

In  address, 

Model

  parameter  should  be  identical  to  printer  name  that  is  displayed  on  the 

print page of print server.

 

2.

 

Select preferred driver by using installation disk.  

3.

 

Installation is finished. 

Also you may use page of advanced printer settings by clicking on the corresponding button. Page view is 

shown below:  

Summary of Contents for TAU-8.IP







































































































Reviews: