Elu ETS41, Manual

E N G L I S H

en - 2

17

Safety instructions

When using Power Tools, always observe the safety regulations
applicable in your country to reduce the risk of fire, electric shock and

personal injury. Read the following safety instructions before attempting

to operate this product. Keep these instructions in a safe place!

General

1 Keep work area clean

Cluttered areas and benches can cause accidents.

2 Consider work area environment

Do not expose Power Tools to humidity. Keep work area well lit.

Do not use Power Tools in the presence of flammable liquids or gases.

3 Guard against electric shock

Prevent body contact with earthed surfaces (e.g. pipes, radiators,

cookers and refrigerators). For use under extreme conditions (e.g. high

humidity, when metal swarf is being produced, etc.) electric safety can

be improved by inserting an isolating transformer or a (FI) earth-leakage

circuit-breaker.

4 Keep children away

Do not let children come into contact with the tool or extension cord.

Supervision is required for those under 16 years of age.

5 Extension cords for outdoor use

When the tool is used outdoors, always use extension cords intended

for outdoor use and marked accordingly.

6 Store idle tools

When not in use, Power Tools must be stored in a dry place and

locked up securely, out of reach of children.

7 Dress properly

Do not wear loose clothing or jewellery. They can be caught in moving

parts. Preferably wear rubber gloves and non-slip footwear when

working outdoors. Wear protective hair covering to keep long hair out
of the way.

8 Wear safety goggles

Also use a face or dust mask in case the operations produce dust or

flying particles.

9 Beware of maximum sound pressure

Take appropriate measures for the protection of hearing if the sound

pressure of 85 dB(A) is exceeded.

10 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees both

hands to operate the tool.

11 Do not overreach

Keep proper footing and balance at all times.

12 Avoid unintentional starting

Do not carry the plugged-in tool with a finger on the switch. Be sure

that the switch is released when plugging in.

13 Stay alert

Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.

14 Disconnect tool

Shut off power and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use, before

servicing or changing accessories.

15 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

16 Use appropriate tool

The intended use is described in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Warning!

 The use of any accessory or attachment and performance of

any operation with this tool, other than those recommended in this

instruction manual may present a risk of personal injury.

17 Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the socket.
Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Inspect the tool cords at regular intervals and,

if damaged, have them repaired by an Elu authorized repair agent.
Inspect the extension cords periodically and replace them if damaged.

Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts

Before using the tool, carefully check it for damage to ensure that it will

operate properly and perform its intended function. Check for

misalignment and seizure of moving parts, breakage of parts and any
other conditions that may affect its operation. Have damaged guards

or other defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. Have the switch replaced

by an Elu authorized repair agent.

20 Have your tool repaired by an Elu authorized repair agent

This Power Tool is in accordance with the relevant safety regulations.
To avoid danger, electric appliances must only be repaired by qualified

technicians.

Additional safety rules for saw benches

• Make sure that the blade rotates in the correct direction and that the

teeth are pointing to the front of the saw bench.

• Be sure all clamp handles are tight before starting any operation.

• Be sure all blade and flanges are clean and the recessed sides of the

collar are against the blade. Tighten the arbor nut securely.

• Keep the saw blade sharp and properly set.

• Make sure that the riving knife is adjusted to the correct distance from

the blade - maximum 5 mm.

• Never operate the saw without the upper and lower guards in place.

• Keep your hands out of the path of the saw blade.

• Disconnect the saw from the mains supply before changing blades or

carrying out maintenance.

• Use a push stick at all times, and ensure that you do not place hands

closer than 150 mm from the saw blade while cutting.

• Do not attempt to operate on anything but the designated voltage.

• Do not apply lubricants to the blade when it is running.

• Do not reach around behind the saw blade.

• Never place either hand in the blade area when the saw is connected

to the electrical power source.

• Replace the table insert when worn.

• During transportation make sure that the upper part of the saw blade is

covered, e.g. by the guard.

• Do not use the guard for handling or transportation.

• Use a holder or wear gloves when handling a saw blade.

• Do not use blades of larger or smaller diameter than recommended.

For the proper blade rating refer to the technical data. Use only the

blades specified in this manual, complying with EN 847-1.

• Consider applying specially designed noise-reduction blades.

• Do not use HSS blades.

• Do not use cracked or damaged saw blades.

• Do not use any abrasive discs.
• Do not cut ferrous metals, non-ferrous metals or masonry.

Residual risks

The following risks are inherent to the use of saws:

- injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.