Elumen8 Kudos 108, User Manual

11- 

(

Notice

: Other settings are NOT changed while choosing Defaults Setting!) 

Press the 

ENTER

 and the corresponding functions will set to defaults setting, to go back to 

the functions without any change press the

 MENU

 button again.

Hold and press the 

MENU

button about one second or wait for one minute to exit the menu mode.

Reset 

Press the 

MENU

 button up to when the 

Reset 

is blinking on the display. Pressing 

ENTER

button and all channels of the unit will return to their standard position.   

3.3 Home Position Adjust   

In the main functions, hold 

Enter 

button for at least 3 seconds into offset mode, use 

DOWN

and 

UP

 button up to chose 

Pan Offset 

or

 Tilt Offset

, pressing 

ENTER

 button and the 

display will blink. Use 

DOWN

 and 

UP

 button to adjust the home position of the Pan, Tilt, 

Once the position has been selected, press the 

ENTER

 button to setup, to go back to the 

functions without any change press the

 MENU

 button again.

Hold and press the 

MENU

button about one second or wait for one minute to exit the menu mode. 

  4. How To Control The Unit   

You can operate the unit in three ways: 

1. Master/slave built-in preprogram function 

  2. Easy controller 

3. Universal DMX controller 

No need to turn the unit off when you change the DMX address, as new DMX address 

setting will be effect at once. Every time you turn the unit on, it will show “CM-108” on the 

display and move all the motors to their ‘home’ position and you may hear some noises for 

about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in 

programs. 

8-

Sound Sense 

Select 

Sound Sense

, press the

 ENTER

 button to confirm, present mode will blink on the 

display. Use the

 DOWN

 and 

UP

 button to select the 

0

…

100

 mode. Once the mode has 

been selected, press the 

ENTER

 button to setup, to go back to the functions without any 

change press the

 MENU

 button again. Hold and press the 

MENU

 button about one second 

or wait for one minute to exit the menu mode. 

Pan Inverse 

Select 

Pan Inverse

, press the 

ENTER

 button to confirm, present mode will blink on the 

display. Use the

 DOWN

 and 

UP

 button to select the

 Yes

 (pan inversion) or 

No

 (normal) 

mode. Once the mode has been selected, press the 

ENTER

 button to setup, to go back to 

the functions without any change press the

 MENU

 button again. Hold and press the 

MENU

button about one second or wait for one minute to exit the menu mode. 

Tilt Inverse 

Select 

Pan Inverse

, press the

 ENTER 

button to confirm, present mode will blink on the 

display. Use the 

DOWN

 and 

UP

 button to select the 

Yes 

(tilt inversion) or 

No

(normal) mode. 

Once the mode has been selected, press the 

ENTER

 button to setup, to go back to the 

functions without any change press the

 MENU

 button again.

Hold and press the 

MENU

button about one second or wait for one minute to exit the menu mode. 

Back Light 

Select 

Back Light

, press the

 ENTER 

button to confirm, present mode will blink on the 

display. Use the

 DOWN

 and 

UP

 button to select the 

On 

(Led on) or 

Off

 (Led off) mode. 

Once the mode has been selected, press the 

ENTER

 button to setup, to go back to the 

functions without any change press the

 MENU

 button again.

Hold and press the 

MENU

button about one second or wait for one minute to exit the menu mode. 

Function Delay 

Select 

Function Delay,

 press ENTER button to confirm, present mode will blink on the 

display. Use 

DOWN

 and 

UP

 button to select the 

No Delay 

or

 1S/2S/3S Delay 

(Wait for 1/2/3 

seconds before these Functions of 12CH are activated/deactivated)

mode. Once the mode 

has been selected, press the 

ENTER

 button to setup, to go back to the functions without any