background image

www.prolight.co.uk

Windstorm DMX Fan

  

User Manual

2

Safety advice

WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL  
CAREFULLY BEFORE YOUR INITIAL START-UP!

•  Before your initial start-up, please make sure that there is no damage caused during transportation.
•  Should there be any damage, consult your dealer and do not use the equipment.
•  To maintain the equipment in good working condition and to ensure safe operation, it is necessary  

for the user to follow the safety instructions and warning notes written in this manual.

•  Please note that damages caused by user modifications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance  
of this manual or any unauthorised modification to the equipment.

 

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and  
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc. 
Do not endanger your own safety and the safety of others! 
Incorrect installation or use can cause serious damage to people and/or property.

•  Never let the power cable come into contact with other 

cables. Handle the power cable and all mains voltage  
connections with particular caution!

•  Never remove warning or informative labels from the unit.
•  Do not open the equipment and do not modify the unit.
•  Do not connect this equipment to a dimmer pack.
•  Do not switch the equipment on and off in short intervals, 

as this will reduce the system’s life.

•  Only use the equipment indoors.
•  Do not expose to flammable sources, liquids or gases.
•  Always disconnect the power from the mains when  

equipment is not in use or before cleaning! Only handle 
the power-cable by the plug. Never pull out the plug by 
pulling the power-cable.

•  Make sure that the available mains supply voltage is 

between 100~240V AC, 50/60Hz.

•  Make sure that the power cable is never crimped or  

damaged. Check the equipment and the power cable 
periodically.

•  If the equipment is dropped or damaged, disconnect the 

mains power supply immediately and have a qualified 
engineer inspect the equipment before operating again. 
 
 
 

•  If the equipment has been exposed to drastic  

temperature fluctuation (e.g. after transportation),  
do not connect power or switch it on immediately.  
The arising condensation might damage the equipment. 
Leave the equipment switched off until it has reached 
room temperature.

•  If your product fails to function correctly, stop use 

immediately. Pack the unit securely (preferably in the  
original packing material), and return it to your Prolight 
dealer for service.

•  Only use fuses of same type and rating.
•  Repairs, servicing and power connection must only be  

carried out by a qualified technician. THIS UNIT CONTAINS 
NO USER SERVICEABLE PARTS.

•  This fixture is for professional use only - it is not designed 

for or suitable for household use. The product must be 
installed by a qualified technician in accordance with local 
territory regulations. The safety of the installation is the 
responsibility of the installer. The fixture presents risks of 
severe injury or death due to fire hazards, electric shock 
and falls.

•  Caution! Never put hands or objects through the protective 

grille, this can cause a risk of injury! People with long hair 
should take special care as long hair can get caught in the 
fan and result in serious injury! Please ensure that air can 
be sucked in freely. Make sure that no dirt, sand, clothing 
or similar can get sucked in.

•  WARRANTY: Two years from date of purchase.

CAUTION!

    KEEP THIS  

      EQUIPMENT AWAY  

         FROM RAIN,  

            MOISTURE  

              AND LIQUIDS

CAUTION!

 TAKE  

   CARE USING THIS  

     EQUIPMENT! HIGH  

        VOLTAGE-RISK  

           OF ELECTRIC  

              SHOCK

CAUTION!

   ROTATING FAN  

      BLADES CAN  

         CAUSE SEVERE  

            INJURY! KEEP  

              HANDS CLEAR!

Summary of Contents for Windstorm DMX Fan









Reviews: