22
1.0
Message language
1.1
Entrance panel ID
1.5
First button ID
1.6
Button remapping 1
1.7
Single pushbuttons
1.8
N° coding digits
1.2
Installation
1.3
Initial ID
1.4
Final ID
1.9
Lock code
2.1
Preferential code
2.2
Lock code
2.0
Preferential code
1.0 - MESSAGE LANGUAGE
Indicates the language selected for messages displayed by the system. To change the language,
press the number on the keypad corresponding to the required language, as indicated in table 1.
BUTTON
0
1
2
3
4
5
LANGUAGE
italiano
inglese
greco
francese
tedesco
spagnolo
portoghese
table 4
Press
to confirm the change. Once the change has been confirmed, the message “Done!”
will appear in the selected language.
Default: Italian
1.1 - ENTRANCE PANEL ID
,GHQWLI\WKHHOHFWURQLFXQLWZLWKDFRGHEHWZHHQDQG>DQG@,IWKHYDOXHLVWKHHOHFWURQLFXQLW
LVVHWDV0$67(5LIWKHYDOXHLVEHWZHHQDQG>D@WKHHOHFWURQLFXQLWLVVHW
as SLAVE.
Enter the identification code using buttons
0
+
to
9
WXYZ
. Press the
button to confirm the
change. Confirming the change, the electronic unit checks the availability of the code. If there
is already another electronic unit connected with the same code, the message
“Panel ID .. already in
use”
ZLOODSSHDUDQGDGLIIHUHQWFRGHPXVWEHHQWHUHG,IWKHFRGHLVDQXPEHUKLJKHUWKDQ>@WKH
message “
Over limit
” will appear; if the identification code is correct, the message “
Done
!” appears.
Pressing 0 will “disable” the electronic unit temporarily.
Default
:
1
1.2 - Installation
Configuration determining installation of the electronic unit on Vertical Bus or Horizontal Bus..
Default: Vertical Bus
1.3 - Initial ID
This item appears only if HORIZONTAL BUS configuration has been selected at step 1.2. The
initial window in which the ID code can operate must be indicated. The rule applies to name
index and self-start functions
.
Default: 1.
1.4 - Final ID
This item appears only if HORIZONTAL BUS configuration has been selected at step 1.2. The
finial window in which the ID code can operate must be indicated. The rule applies to name index
and self-start functions.
Default: 1000
1.5 - FIRST BUTTON ID
Configuration relating to additional button modules 12TS and 12TD (if installed). Press a button
with the number to allocate and confirm with
. The change is confirmed by the message “
Done
”.
With this configuration, a number is allocated to the first button of tradition button modules. If
the first button is identified as ID = 3, the second button will be ID = 4, and so on.
Default: 1
1.6 - BUTTON REMAPPING
Configuration relating to additional button modules 12TS and 12TD. When the message
Remap
Button 1
is displayed on the first line, enter the number to be allocated: the
Remap Button
message
will appear with confirmation of the number just indicated; enter the number of the button
and confirm with
. The change is confirmed by the message “Done”.
With this configuration, a number is allocated to the first button of traditional button modules.
If the first button is identified as ID = 3, the second button will be ID = 4, and so on.
Default: 0
1.7 - SINGLE BUTTONS
Configuration relating to additional button modules 12TS and 12TD. When the message
SINGLE
BUTTONS
is displayed on the first line, press 1 = YES to configure the buttons in a single row,
or 0 = NO to configure the buttons in a double row and confirm with
.
The change is confirmed by the message “
Done
”.
Default: Yes
