background image

PPC-E4-3354_User_Manual.docx

 

-11- 

Rev 1.0  © 2016 EMAC, Inc.

 

 

 

2.6 

MicroSD Card Socket 

 

The PPC-E4-3354 provides a high capacity MicroSD socket. This socket is hot-swappable and can accept a wide 
variety  of Flash Cards.  A  green activity  light (LED  LD2) is located towards the  left side of the socket. W hen the 
processor is accessing the Flash card, this LED will be lit and the card should not be removed at this time. A card 
that  is  written  to  by  the  PPC-E4-3354,  can  be  read  by  another  computer,  using  a  MicroSD  card  reader.  The 
MicroSD interface is compatible with Standard and High Capacity MicroSD cards. 

 

 

2.7

 

Keyboard/Mouse 

The  PPC-E4-3354  does  not  provide  a  PS/2  type  keyboard/mouse  interface.  However,  a  USB  keyboard  and 
mouse can be used if required. 
 

2.8

 

Analog Inputs  

The analog inputs are available on HDR1 (see table below) and are labeled as analg_04, analg_05, analg_06 and 
analog_07.  Voltages applied to the inputs must be in the range of 0V to 3.3V with reference to ground. Different 
operating  systems  may  provide  access  to  the  analog  inputs  differently  or  even  not  at  all.    See  the  operating 
system documentation for details. Note: In some cases using the Analog Inputs can have adverse  effect on the 
touchscreen sensitivity. 
 

2.9

 

I/O Expansion  

The  Processor  used  by  the  PPC-E4-3354  provides  a  number  of  unused  I/O  lines.  The  PPC-E4-3354  provides 
access  to  these  lines  on  connector  HDR1.  This  20-pin  dual  row  header  contains  GPIO  lines,  SPI  bus,  I

2

C  bus, 

A/D lines, interrupts and power pins. Signal names listed in the table below are the SoM names as defined in the 
SoM 200 pin specification. 
 
Table 8 

Pin

 

Signal  

Pin 

Signal 

 

1  

GND  

3.3V

 

3  

I2DAT  

I2CLK

 

5  

~RESET_OUT  

6  

SPI_MISO

 

7  

SPI_CLK  

8  

SPI_MOSI

 

9  

SPI_CS1  

10 

SPI_CS0 

 

11  

SPI_CS3 

12 

GPIO07

 

13  

ANALG_05  

14 

GPIO13 

 

15  

ANALG_06  

16 

IROA 

 

17  

ANALG_04  

18 

GPIO15

 

19  

ANALG_07  

20 

GPIO12 

 

 

 

 
 

2.10 

Real-Time Clock 

 

The PPC-E4-3354 emulates a real time clock using the internal real time clock on the AM3354 processor. Battery 
backup is provided from the carrier board using the VSTBY pin.  The real-time clock is a precise timer which can 
generate interrupts on intervals specified by the user. 
 

Summary of Contents for PPC-E4-3354





















Reviews: