background image

PPC-E4+ User Manual.doc

 

-1- 

Rev 1.4  © 2015 EMAC, Inc.

 

 

Disclaimer

 

 

EMAC  Inc.  does  not  assume  any  liability  arising  out  of  the  application  or  use  of  any  of  its  products  or  designs.  
Products designed or distributed by EMAC Inc. are not intended for, or authorized to be used in, applications such 
as life support systems or for any other use in which the failure of the product could potentially  result in personal 
injury, death or property damage. 
 
If EMAC Inc. products are used in any of the aforementioned unintended or unauthorized applications, Purchaser 
shall indemnify and hold EMAC Inc. and its  employees and officers harmless against all claims, costs, damages, 
expenses,  and  attorney  fees  that  may  directly  or  indirectly  arise  out  of  any  claim  of  personal  injury,  death  or 
property damage associated with such unintended or unauthorized use, even if it is alleged that EMAC Inc. was 
negligent in the design or manufacture of the product. 
 
EMAC Inc. reserves the right to make changes to any products with the intent to improve overall quality, without 
further notification.

 

Summary of Contents for PPC-E4+




















Reviews: