9
Hydrostatic transmission:
4.31
BRAKE PEDAL (Fig. 4.3 no.31)
This pedal works the brake on the rear
wheels.
4.32
CLUTCH PEDAL (Fig. 4.3 no.32)
This pedal engages drive in the wheels and
controls the machine’s forward and reverse
speed.
– To engage forward gear just press it in the
«F» direction with the tip of your foot, not
-
ing that increasing the pressure on the
pedal progressively increases the speed
of the machine.
– Reverse is engaged by pressing the pedal
with the heel towards «R».
– The pedal automatically goes into neutral
«N» when released.
WARNING!
Reverse must be en-
gaged when the machine has stopped.
NOTE
If the drive pedal is used, wheth-
er forwards or for reverse, when the parking
brake (4.4) is engaged, the engine stops.
4.33
HYDROSTATIC TRANSMISSION
DISENGAGEMENT LEVER
(Fig. 4.3 no.33)
This lever has two positions as shown on the
label:
«
A
» = Transmission engaged: for all uses,
when moving and during cutting;
«
B
» = Transmission disengaged: this
makes it much easier to move the
machine by hand,
with the engine
turned off.
IMPORTANT
To avoid damaging the
transmission unit, this operation must be car-
ried out only when the engine has stopped
with the pedal (4.32) at position «N”.
5. OPERATING INSTRUCTIONS
5.1
SAFETY RECOMMENDATIONS
WARNING!
If the machine is likely to
be used mostly on sloping ground (never
steeper than 10°), fit counterweights (sup-
plied on request (see 8.1) beneath the cross-
member of the front wheels. These improve
stability at the front and reduce the chances
of tipping over.
IMPORTANT
All the references relating to
the positions of controls are those described in
chapter 4.
5.2
WHY THE SAFETY DEVICES CUT IN
The safety devices work in two ways:
– they prevent the engine from starting if all the
safety requirements have not been met;
– by stopping the engine if even just one of the
safety requirements is lacking.
a
) To start the engine, it is necessary that:
– the transmission is in “neutral”;
– all the cutting means are disengaged;
– the operator is seated.
b
) The engine stops when:
– the operator leaves his seat;
– the grass catcher is lifted or the rear dis
-
charge guard removed without disengaging
the cutting means;
– the parking brake is engaged without disen
-
gaging the cutting means;
– the speed change (see 4.22) or the drive
pedal (see 4.32) is activated with the parking
brake on.
5.3
PRELIMINARY OPERATIONS BEFORE
STARTING WORK
Before starting to mow, it is necessary to carry
out several checks and operations to ensure
you can work efficiently and in maximum safety.
5.3.1
Seat adjustment (Fig. 5.1)
To change the seat position, loosen the four fix
-
ing bolts (1) and slide it along the slots.
Once you have found the right position, tighten
the four screws (1) thoroughly.
5.3.2
Tyre pressure (Fig. 5.2)
Having the right tyre pressure is the main condi
-
tion for ensuring that the cutting-means assem
-
bly is horizontal and mows evenly.
Unscrew the valve caps and connect a com
-
pressed air line with a gauge to the valves and
adjust the pressure to the indicated values.
5.3.3
Filling with oil and fuel
NOTE
The type of oil and fuel to use is given
in the engine manual.
With the engine off, check the oil level. Accord
-
ing to the instructions in the engine manual, this
must be between the MIN and MAX marks on
the dipstick. Fig. 5.3)
Summary of Contents for KJK 102H Series
