EN - 23
PROBLEM
PROBABLE CAUSE
REMEDY
4.
With the key turned to
«START» the starter
motor does not run
(for side discharge
models only)
Turn the ignition key to «STOP» position
and look for the cause of the problem:
starting conditions have not been met
check that all starting conditions are met
(par. 6.2.2)
badly connected battery
check the connections (par. 4.4)
battery terminals crossed
check the connections (par. 4.4)
flat battery
recharge the battery (par. 7.5)
fuse blown
replace fuse (10 A) (par. 8.5).
wet circuit board
dry using luke warm air
malfunction on the starter relay
contact your Dealer
5. With the key on
«START» the starter
motor runs but the
engine does not start
insufficiently charged battery
recharge the battery (par. 7.5)
faulty fuel supply
check the level in the tank (par. 7.2.1)
open the fuel stopcock (if
foreseen) (par. 6.4)
check the fuel filter
faulty ignition
check that spark plug cap is securely fitted
check that the electrodes are clean
and have the correct gap
6.
Starting is difficult or the
engine runs erratically
carburation problems
clean or replace the air filter
empty the fuel tank and refill with fresh fuel
check and replace the fuel filter if necessary
7. Weak engine
performance
during cutting
forward speed too high in
relation to cutting height
reduce the forward speed and/or
raise the cutting height (par. 6.5.4)
8.
The engine shuts
down whilst working
the safety devices have cut in
check that all starting conditions
are met (par. 6.2.2)
blown fuse due to a short circuit
or electrical system faults
(
for
side discharge models only)
The cause of the fault should be
ascertained and dealt with to avoid
reactivating the protection device
Replace the fuse (10 A) (par. 8.5).
Contact your Dealer if such
interruptions continue
9. The engine stops whilst
operating and the
indicator light switches
off
(for rear collection
models only)
The safety device of the electronic
circuit board has cut in due to:
Turn the ignition key to «STOP», wait
for a couple of seconds to allow the
circuit to reset automatically and:
battery terminals crossed
check the connections (par. 4.4)
faults in the battery charging regulator
check the battery connections (par. 4.4)
check the battery is fitted
short circuit
contact your Dealer
10.
The cutting means do
not engage or do not
stop promptly when
they are disengaged
problems with engagement mechanism
contact your Dealer
If problems persist after having performed the above operations, contact your dealer.
Summary of Contents for KLX 108 Series
