background image

T h i s  a p p l i a n c e  c o n t a i n s  f l u o r i n a te d  g re e n h o u s e  g a s e s : 

installation  must  be  carried  out  by  an  installer  |  company 

authorized  in  accordance  with  the  European  regulation  EU 

517|2014.

All  the  drawings  shown  in  this  manual  relating  to  electrical, 

hydraulic  or  gas  installation  systems  must  be  understood  to  be 

purely  illustrative.  All  the  safety  devices,  auxiliar y  devices  and 

the  diameters  of  the  electrical,  hydraulic  and  gas  pipes  must  always  be 

checked by a professionally qualified technician, to make sure they satisfy the 

applicable laws and regulations.

P3    PROHIBITION

PROHIBITION:

Water  or  any  kind  of  liquid  is  strictly  forbidden  to  be  poured  into  the 

product, or may cause electric creepage or breakdown of the product.

Use  the  proper  fuse  and  breaker.  It  is  forbidden  to  use  copper  or  steel 

wires to replace the fuse or switch.

Do  not  touch  the  fins  of  the  evaporative  condensing  batter y,  they  can 

hurt your fingers.

FAILURE  TO  FOLLOW  THESE  WARNINGS  MAY  RESULT  IN  PROPERTY  DAMAGE, 

ELECTRIC SHOCK, ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.

Safety Precautions(R32)

Meanings of symbols displayed on heat pump unit

1.Since rotating parts and parts which could cause an electric shock are used in this 

product, be sure to read these "Safety Precautions" before use.

WARNING

This unit uses a flammable refrigerant (1132).
If refrigerant leaks and comes in contact with fire or heating part, it 
will create harmful gas and

Read the OPERATING INSTRUCTIONS carefully before operation.

Ser vice personnel are required to carefully read the OPERATING INSTRUCTIONS
and INSTALLATION MANUAL before operation.

Further information is available in the OPERATING INSTRUCTIONS, INSTALLATION
MANUAL, and the like.

2.Since the cautionar y items shown here are important for safety, be sure to obser ve       

them.

3.After reading this manual, keep it together with the installation manual in a handy 

place for easy reference.

4.Be sure to receive a guarantee card from your dealer and check that the purchased data 

and shop name, etc. are entered correctly.

WARNING

Incorrect handling could cause serious hazard, such as 
death, serious injur y, etc. with a high probability.

Incorrect handling could cause serious hazard depending
on the conditions.

CAUTION

Meanings of symbols used in this manual

Meanings of symbols used in this manual

Be sure not to do.

Be sure to follow the instruction.

Never insert your finger or stick , etc.

Never step into the indoor/outdoor unit and do not put anything on them.

Damager of electric shock . Be careful.

Be sure to disconnect the power supply plug from the power outlet.

Be sure to shut off the power.

Risk of fire.

PROHIBITION    P4

Summary of Contents for 31000001






















Reviews: