background image

11

Repair Parts Listing

Part Numbers

Key

Model No.

Model No.

No. Description

ACF552ORB00

ACF552WW00

*

Hanger Ball Assembly,

761655-32

761655

Consisting of:

1

Hanger Bracket

2

Hanger Ball

3

Downrod

*

Parts Bag Containing:

763913-BLOXSS 763913-SS

4

Pin, Clevis (1)

5

Clip, Hairpin (1)

6

Stud, Threaded, #8-32 x 1-1/4” (2)

7

Lockwasher, External Tooth, #8 (2)

8

Nut, Knurled, #8-32 (2)

9

Screw, Serrated Pan Head,

M4 x 10mm (1)

10

Screw, Flat Head, M4 x 12mm (1)

11

Screw, Washer Head Blade (16)

12

Screw, M6 x 14mm Pan Head

with Lockwasher (1)

13

Balancing Kit (1)

14

Pad, Canopy Seal

764376

764376

15

Cover, Ceiling

763921-ORB

763921-WW

16

Cover, Coupling

764054-ORB

764054-WW

17

Harness, Wiring

764375-BLK

764375-WW

18

Switch Cup Cover

763915-ORB

763915-WW

19

Switch Cup 

763919-ORB

763919-WW

20

Fan Blades (set of 5)

763910-ORB

763910-WW

21

Blade Flanges (set of 5)

763908-ORB

763908-WW

Owner's Manual

BP7461

BP7461

Before discarding packaging material, be certain all parts have been removed.

HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

• PART NUMBER

• NAME OF ITEM

• PART DESCRIPTION

• MODEL NUMBER

The model number of your Fan will be found on a label attached to the top housing.

For repair parts:

Model No.: ACF552

Ceiling  fan  performance  and  energy  savings
rely heavily on the proper installation and use
of the ceiling fan. Here are a few tips to ensure
quality and product performance.

Choosing  the  Appropriate  Mounting
Location. 

Ceiling fans should be installed, or

mounted,  in  the  middle  of  the  room  and  at
least 2.1 m above the floor and 50 cm from the
walls.  If  ceiling  height  allows,  install  the  fan
2.4m - 2.7m above the floor for optimal airflow. 

Using  the  Ceiling  Fan  Year  Round.

In  the

summer,  use  the  ceiling  fan  in  the  counter-
clockwise  direction.  The  airflow  produced  by
the  ceiling  fan  creates  a  wind-chill  effect,
making  you  "feel"  cooler.  Select  a  fan  speed
that  provides  a  comfortable  breeze,  lower
speeds  consume  less  energy.  In  the  winter,
reverse  the  motor  and  operate  the  ceiling  fan
at  low  speed  in  the  clockwise  direction.  This
produces a gentle updraft, which forces warm
air  near  the  ceiling  down  into  the  occupied
space.  Remember  to  adjust  your  AIRCON
thermostat  when  using  your  ceiling  fan  -
additional  energy  and  dollar  savings  could  be
realized with this simple step! 

Turn  Off  When  Not  in  the  Room. 

Ceiling

fans  cool  people,  not  rooms.  If  the  room  is
unoccupied,  turn  off  the  ceiling  fan  to  save
energy.

Energy Efficient Use of

Ceiling Fans

Phone: 1300 469 326

info@myfan.com.au

www.myfan.com.au

Summary of Contents for ACF552ORB00













Reviews: