background image

 

 

 

Form 297-LB Rev. 01/2014 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ASCO Power Technologies

 

6255 Halle Drive

 

Cleveland, OH 44125

 

T (216) 573 7600

 

F (216) 573 5953

 

www.avtronloadbank.com

 

If  replacement  parts,  components  or  products  are  shipped  or  caused  to  be  shipped  by  ASCO  prior  to  inspection  of  the  product 
claimed  to  be  defective,  the  replacement  parts,  components  or  products  shall  be  invoiced  in  the  full  current  price  amount  and 
shipped freight collect F.O.B. 

ASCO’s facility. If ASCO’s inspection determines that the returned item(s) is covered by this warranty, 

User will be issued a credit in an amount equal to the parts prices previously invoiced.  Warranty coverage will be provided only after 
ASCO’s  inspection  discloses  the  claimed  defect  and  shows  no  signs  of  treatment  or  use  which  would  void  the  coverage  of  this 
Warranty.  All defective products and component parts replaced under this warranty become the property of ASCO. 

 
Warranty Performance of Component Manufacturers:

 

It is ASCO’s practice, consistent with its desire to remedy Warranty defects in the most prompt and effective manner possible, to 
cooperate with and utilize the services of component manufacturers and their authorized representatives in the performance of work 
to  correct  defects  in  the  product  components.  Accordingly,  ASCO  may  utilize  third  parties  in  the  performance  of  Warranty  work, 
including repair or replacement hereunder, where, in ASCO's opinion, such work can be performed in less time, with less expense, 
or in closer proximity to the Avtron product.  
 

Items Not Covered By Warranty:

 

THIS WARRANTY  DOES  NOT  COVER  DAMAGE  OR  DEFECT  CAUSED BY misuse,  improper  application,  wrong  or  inadequate 
electrical current or connection, negligence, inappropriate on site operating conditions, repair by non-Avtron designated personnel, 
accident in transit, tampering, alterations, a change in location or operating use, exposure to the elements, water, or other corrosive 
liquids or gases, Acts of God, theft, installation and/or deployment contrary to ASCO's recommendations or specifications, or in any 
event if the Avtron serial number has been altered, defaced, or removed.  
 
THIS WARRANTY  DOES  NOT  COVER shipping  costs,  installation  costs,  or  maintenance  or  service  items  and  further,  except  as 
may be provided herein, does NOT include labor costs or transportation charges arising from the replacement of the Avtron product 
or any part thereof or charges to remove or reinstall same at any premises of User. 
 
REPAIR  OR  REPLACEMENT  OF  A  DEFECTIVE  PRODUCT  OR  PART  THEREOF  DOES  NOT  EXTEND  THE  ORIGINAL 
WARRANTY PERIOD. 
 
THE  PRODUCTS  LISTED  IN  THIS  WARRANTY  ARE  NOT  FOR  USE  IN  THE  CONTROL  AREA  OR  ANY  REACTOR 
CONNECTED  OR  SAFETY  APPLICATIONS  OR  WITHIN  THE  CONTAINMENT  AREA  OF  A  NUCLEAR  FACILITY  OR  FOR 
INTEGRATION INTO MEDICAL DEVICES. 
 

Limitations:

 

THIS  WARRANTY  IS  IN  LIEU  OF  AND  EXCLUDES  ALL  OTHER  WARRANTIES,  EXPRESS  OR  IMPLIED,  INCLUDING 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 
 
USER'S  SOLE  AND  EXCLUSIVE  REMEDY  IS  REPAIR  OR  REPLACEMENT  OF  THE  AVTRON  PRODUCT  AS  SET  FORTH 
HEREIN. 
 
IF  USER'S  REMEDY  IS  DEEMED  TO  FAIL  OF  ITS  ESSENTIAL  PURPOSE  BY  A  COURT  OF  COMPETENT  JURISDICTION, 
AVTRON’S  RESPONSIBILITY  FOR  PROPERTY  LOSS  OR  DAMAGE  SHALL  NOT EXCEED  THE  NET PRODUCT  PURCHASE 
PRICE. 
 
IN  NO  EVENT  SHALL  ASCO  ASSUME  ANY  LIABILITY  FOR  INDIRECT,  SPECIAL,  INCIDENTAL,  CONSEQUENTIAL  OR 
EXEMPLARY  DAMAGES  OF  ANY  KIND  WHATSOEVER,  INCLUDING  WITHOUT  LIMITATION  LOST  PROFITS,  BUSINESS 
INTERRUPTION  OR  LOSS  OF  DATA,  WHETHER  ANY  CLAIM  IS  BASED  UPON  THEORIES  OF  CONTRACT,  NEGLIGENCE, 
STRICT LIABILITY, TORT, OR OTHERWISE. 
 

Miscellaneous

NO  SALESPERSON,  EMPLOYEE  OR  AGENT  OF  ASCO  IS  AUTHORIZED  TO  ADD  TO  OR  VARY  THE  TERMS  OF  THIS 
WARRANTY. Warranty terms may be modified, if at all, only in writing signed by an ASCO officer

.

 

 
ASCO obligations under this Warranty are conditioned upon ASCO timely receipt of full payment of the product purchase price and 
any other amounts due.  ASCO reserves the right to supplement or change the terms of this Warranty in any subsequent warranty 
offering to User or others. 
 
In the event that any provision of this Warranty should be or becomes invalid and/or unenforceable during the warranty period, the 
remaining terms and provisions shall continue in full force and effect. 
 
This Warranty shall be governed by, and construed under, the laws of the State of New Jersey, without reference to the conflict of 
laws principles thereof. 
 
This Warranty represents the entire agreement between ASCO and User with respect to the subject matter herein and supersedes 
all prior or contemporaneous oral or written communications, representations, understandings or agreements relating to this subject.

 

 

Summary of Contents for AVTRON LOADBANK LPH400


































Reviews: