background image

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver
One 1/4" blade screwdriver
One stepladder
One wire stripper
Three wire connectors (supplied)

Materials

Wiring electrical box and box connectors must be of
type required by local code. The minimum wire would
be a 3-conductor (2-wire with ground) of size shown at
right.

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50 - 100 ft.

12

1.Check to see that you have received the following

parts:

NOTE: If you are uncertain of part description,
refer to exploded view illustration.

a. Fan housing
b. Mounting plate

c. Fan motor assembly

d. Five fan blades
e. Five blade flanges

f. One loose parts bag containing:

1. Sixteen 3/16-24 x 9/32" phillips washer 

head screws.

2. One wood ball with chain.
3. Three wire connectors.
4. Four 3/16-24 x 5/8" housing screws.
5. Four 1/4" hex locknuts.
6. Eleven 1/4-20 x 1/2" phillips head screws.

NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost. If
any parts are missing, contact your local retailer
or catalog outlet for replacement before
proceeding.

2. Remove the fan assembly from the protective

plastic bag. Place the fan assembly into the upper
foam pad with the lead wires up.

Unpacking Instructions

For your convenience, check-off boxes are provide next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.

FAN
BLADES

UPPER
FOAM PAD

MOUNTING
PLATE

FAN
HOUSING

BLADE FLANGES

FAN
MOTOR
ASSEMBLY

LOWER
FOAM PAD

CARTON

3

Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 5). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

WARNING

!

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.

WARNING

!

WARNING

!

Summary of Contents for CF804SAB









Reviews: