- 11 -
EN
9J27
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE:
Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then
select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1
Plug in the TV/VCR power cord
Plug the TV/VCR power cord into a
standard AC outlet.
NOTES:
•
You must disconnect the car battery
cord from the TV/VCR before you
use AC power.
•
If some digits appear in the corner
of the screen, press the POWER button without
unplugging the power cord.
2
Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
3
Select “ENGLISH” or “ESPAÑOL”
Select “ENGLISH” or
“ESPAÑOL”=Spanish using the
F.FWD/
B
or REW/
s
button. “[ ]”
indicate the selected language.
4
Begin auto preset
Press the PLAY/
K
or STOP/
L
but-
ton to point to “AUTO PRESET”.
Then press the F.FWD/
B
button.
The tuner scans and memorizes all
active channels in your area.
NOTES:
•
The TV/VCR distinguishes between standard TV
channels and cable channels.
•
If you want to play or record a video tape BEFORE
presetting the tuner, you must press the MENU but-
ton on the remote control. To preset the tuner again,
see “CHANNEL SET UP AGAIN” on page 13.
•
The TV/VCR may recognize TV channels to be
CATV channels by the receiving conditions. In this
case, try auto preset again in the fine receiving
conditions.
5
After scanning
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote
control number buttons or CHANNEL
K
or
L
button.
– SET UP –
B
LANGUAGE
[ENGLISH] ESPAÑOL
AUTO PRESET
– SET UP –
LANGUAGE
[ENGLISH] ESPAÑOL
B
AUTO PRESET
TO SELECT A DESIRED CHANNEL
You can select the desires channel by using the
CHANNEL
K
or
L
button on or directly pressing
the number buttons on the remote control.
Note for using the number buttons:
•
When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
•
You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).
CLOCK SET UP
(AUTO / MANUAL)
The TV/VCR clock must be set correctly before
VCR timer recording is possible. It is suggested that
the clock be set manually when first setting up the
TV/VCR. Then, set to [ON] the auto clock setting
which will periodically correct the setting if neces-
sary.
NOTE:
If you cannot receive a station with time sig-
nals, auto clock setting cannot be performed. Use
manual setting only.
MANUAL CLOCK SETTING
Make sure ...
•
The TV/VCR is turned on.
In the example below, the clock is to be set to:
DATE
May 6th, 2003
SETTING TIME
5:40PM
1
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/
K
or STOP/
L
but-
ton to point to “SETTING
CLOCK”.
Then, press the F.FWD/
B
button.
2
Select “MANUAL CLOCK SET”
Press the PLAY/
K
or STOP/
L
but-
ton to point to “MANUAL
CLOCK SET”.
Then, press the F.FWD/
B
button.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
B
MANUAL CLOCK SET
D.S.T.
[OFF]
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
T4403UD.QX33 02.12.24 4:47 PM Page 11
