background image

Introduction

This installation guide provides instructions for installation, 

startup and adjustment. To receive a copy of the 

instruction manual, contact your local Sales Office or view 

a copy at www.fisher.com. For further information refer to: 

Type EZR Relief Instruction Manual, D102629X012.

P.E.D. Categories

This product may be used as a pressure accessory with 

pressure equipment in the following Pressure Equipment 

Directive categories. It may also be used outside of the 

Pressure Equipment Directive using sound engineering 

practice (SEP) per table below. For information on the 

current PED revision see Bulletin: 

D103053X012.

PRODUCT SIZE

CATEGORIES

FLUID GROUP

DN 25, 50, 80, 100 and 150 /

NPS 1, 2, 3, 4 and 6

III

1

Specifications 

Main Valve Body Size, End Connection Styles  

and Body Ratings

(1)

See Table 1

Maximum Relief (Inlet) Pressure

(1)

See Tables 2 and 5

Minimum Relief Set Pressure

(1)

1.4 bar / 20 psig

Set Pressure Control Ranges

See Table 2

Temperature Capabilities

(1)

See Table 4

Installation

!

WARNING

Only qualified personnel should install 

or service a backpressure regulator. 

Backpressure regulator should be 

installed, operated and maintained 

in accordance with international and 

applicable codes and regulations 

and Emerson Process Management 

Regulator Technologies, 

Inc. instructions.

1. The pressure/temperature limits in this installation guide and any applicable standard or code limitation should not be exceeded.

If using a backpressure regulator on a 

hazardous or flammable fluid service, 

personal injury and property damage 

could occur due to fire or explosion of 

vented fluid that may have accumulated. 

To prevent such injury or damage, 

provide piping or tubing to vent the 

fluid to a safe, well-ventilated area or 

containment vessel. Also, when venting 

a hazardous fluid, the piping or tubing 

should be located far enough away 

from any buildings or windows so to 

not create a further hazard, and the vent 

opening should be protected against 

anything that could clog it.

Personal injury, equipment damage 

or leakage due to escaping fluid or 

bursting of pressure-containing parts 

may result if this backpressure regulator 

is overpressured or is installed where 

service conditions could exceed the limits 

given in the Specifications section, or 

where conditions exceed any ratings of 

the adjacent piping or piping connections.
To avoid such injury or damage, provide 

pressure-relieving or pressure-limiting 

devices (as required by the appropriate 

code, regulation or standard) to prevent 

service conditions from exceeding limits.

Additionally, physical damage to the 

backpressure regulator could result in 

personal injury and property damage due 

to escaping fluid. To avoid such injury and 

damage, install the backpressure regulator 

in a safe location.

Clean out all pipelines before installation of the 

backpressure regulator and check to be sure the 

backpressure regulator has not been damaged or has 

collected foreign material during shipping. For NPT 

bodies, apply pipe compound to the external pipe 

threads. For flanged bodies, use suitable line gaskets 

and approved piping and bolting practices. Install the 

backpressure regulator in any position desired, unless 

otherwise specified, but be sure flow through the body 

is in the direction indicated by the arrow on the body.

Type EZR Relief

Installation Guide

D102629X014
English – October 2015

Summary of Contents for Fisher EZR Relief









Reviews: