5. Slide the guide plate(5) up the light
fitter’s threaded nipple until the glass
shade(1) mates with the bottom of the
light fitter plate (Figure 6).
6. Install the hex nut onto the threaded
nipple and firmly hand tighten the nut to
secure the guide plate(5) and glass
shade(1) onto the light fitter(2).
7. Slide the fan switch chain(3) through
the side hole of the glass cap and slide
the light fitter chain(4) through the
center hole of the glass cap(6). Slide
the glass cap(6) up the threaded nipple
until it rests against the bottom of the
glass shade(1) (Figure 6).
8. Pass the light fitter chain(4) through the
center of the finial nut and fasten the
finial nut(7) onto the fitter nipple. Gently
hand tighten the finial nut(7) up against
the bottom of the glass cap(6) to secure
it in position (Figure 6).
9. Reinstall the fan switch pendant(8) to
the fan switch chain(3) (Figure 6).
10. Installation is now complete. Turn on
the electricity at the main fuse or
circuit breaker box.
5
4
11. Position the cup/light fitter(1)(7) on
the cover plate(2) and install the
three screws(3) that were previously
removed in Step 2 and tighten
securely.
12. Proceed to “Installation of
Fluorescent Bulbs and Glass Shade”
section.
Installation on Emerson
Fans Having Two-Piece
Die-Cast Switch
Housings
1. Remove all parts and parts packages
from carton.
2. Remove the cover(5) from the fan
switch housing(1) by removing the two
outer screws(2). (See Figure 4).
3. Remove the center screw(4) from the
cover(5). Insert the black and white
wires from the light fitter(6) thru the
hole and thread the switch housing
cover tightly onto the light fitter.
4. Insert the black and white wires through
the lockwasher(8) and hex nut(7)
supplied. Firmly tighten the hex nut to
secure the light fitter to the switch
housing cover(5).
(3) WIRE
CONNECTORS
WHITE WIRES
BLUE WIRE
BLACK WIRE
FAN SWITCH
CHAIN
(1) SWITCH
HOUSING
ASSEMBLY
(5) COVER
(2) SCREWS
(4) CENTER
SCREW
(8) LOCKWASHER
(7) HEX NUT
(6) LIGHT FITTER
Figure 4
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.
WARNING
!
To avoid possible electric shock, be sure
electricity is turned off at the main fuse
or circuit breaker box before wiring.
WARNING
!
5. Carefully locate the white and blue
wires (labeled either “L” or “LIGHT”) in
the switch housing. Remove and retain
the wire connectors(3) from the wires.
6. Connect the white wire from the ceiling
fan to the white wire of the light fitter(6).
Connect the blue wire from the ceiling
fan to the black wire of the light fitter.
Use U.L. listed wire connectors(3)
(previously removed in Step 5) to make
connections. (Figures 3 and 4.)
7. Carefully tuck all wires and splices into
the switch housing(1).
8. Attach the cover/light fitter(5)(6) to the
switch assembly housing(1) using the
two outer screws(2) that were removed
in Step 2) (Figure 4.)
9. Proceed to “Installation of Fluorescent
Bulbs and Glass Shade” section.
To avoid fire or electrical shock, be
careful not to pinch wires between
the switch housing assembly and
the cover.
WARNING
!
Installation of
Fluorescent Bulbs and
Glass Shade
1. Carefully position one of the GU24
fluorescent bulbs(1) (supplied) into the
light fitter socket. Twist the bulb
clockwise, approximately 1/16 turn, to
engage the bulbs pins into the light
fitter socket holes(2) (Figure 5). Install
the remaining three GU24 fluorescent
bulbs in the same manner.
2. Remove the fan switch pendant(3) from
the fan switch chain(4) for installation of
glass. Place the fan switch chain
through the light fitter plate(5) hole
(Figure 5).
3. Place glass shade (1) onto light fitter(2)
making sure that both fan switch
chain(3) and light fitter chain(4) are
positioned through the center hole in
glass shade(1) (Figure 6).
4. Slide the switch chain(3) through the
side hole of the guide plate(5) and the
light fitter chain(4) through the center
hole of the guide plate(5) (Figure 6).
To avoid fire hazard, do not exceed
wattage indicated on the fixture.
WARNING
!
THREADED
NIPPLE
(2) LIGHT FITTER
13-WATT GU24
FLUORESCENT BULB
(1) GLASS
SHADE
(3) FAN SWITCH
CHAIN
(4) LIGHT FITTER
CHAIN
(5) GUIDE PLATE
(8) FAN SWITCH
PENDANT
(7) FINIAL NUT
(9) LIGHT SWITCH
PENDANT/COUPLING
(6) GLASS CAP
HEX NUT
LIGHT FITTER
PLATE
Figure 6
(1) 13-WATT GU24
FLUORESCENT BULB (4)
(2) LIGHT FITTER
SOCKET
(5) LIGHT FITTER
PLATE HOLES
(4) FAN SWITCH
CHAIN
(3) FAN SWITCH
PENDANT
LIGHT FITTER
PLATE
Figure 5
