background image

7

emersonfans.com

Please contact 1-800-654-3545 for further assistance

U.L. Model No.: CF2000

AT LEAST

7'

FLOOR

CEILING

Figure 6

TWO SCREWS
SUPPLIED WITH
OUTLET BOX

HANGER
BRACKET

TAB

OUTLET
BOX

Figure 7

OUTLET
BOX

HANGER
BRACKET

HANGER BALL/
DOWNROD  
ASSEMBLY

NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES 
OMITTED FOR CLARITY.

Figure 8

How to Hang Your Ceiling Fan

The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7kg. (50 lbs.) or less”.

WARNING

!

Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.

WARNING

!

To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.

WARNING

!

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.

WARNING

!

The fan must be hung with at least 7' of clearance from
floor to blades (Figure 6).

WARNING

!

1.

Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 7.)

2.

Carefully lift the fan and seat the hanger ball/
downrod assembly on the hanger bracket that was
just attached to the outlet box (Figure 8). Be sure the
groove in the ball is lined up with tab on the hanger
bracket (Figure 7).

Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.

WARNING

!

NOTE: For ease of installation, first the fan motor and
housing assembly is installed on the ceiling. Then
after wiring of the fan is completed, the fan blade
assemblies will be attached to the motor hub.

Summary of Contents for MAUI BAY CF2000AB02

















Reviews: