background image

ON

1

2

3

4

RECEIVER SWITCH
LEVERS

CODE
SWITCH

SW105 RECEIVER

CODE
SWITCH

WALL 
CONTROL

WALL CONTROL
LEVERS

ON

1

2

3

4

LIGHT

HI

HI

MED

MED

LOW

LOW

FAN  OFF

Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box.

!

WARNING

13

Battery Installation of

Wall Control

Figure 24

Setting Operating

Frequency of Wall

Control and Receiver

(Figure 24)

Your wall control and receiver have code
switches which must be set in one of 16
possible code combinations. The four
levers (numbered 1, 2, 3, and 4) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:

1. Slide the four switch levers in the wall

control to your choice of ON (up) or
down positions. Use a ball-point pen or
small screwdriver and slide the levers
firmly up or down.

2. In the receiver, slide the four switch

levers to the same positions as set in
the wall control. Make sure the levers
on both switches are in the same
positions, otherwise the fan will not
operate.

The wall control transmits the
command signals via radio waves to
the SW105 receiver installed in the
ceiling fan ceiling cover. The SW105
receiver is required for the wall control
to function. Power for the wall control
comes from the 12V battery, located in
the wall control.

Replacement 12V batteries recom-
mended are Duracell MN21, Eveready
A23, and GP23A.

1. Install the 12V battery (supplied) into

the wall control (Figure 25). 

2. The wall control is supplied with a white

or almond color cover. Choose the style
that best suits your needs and snap the
cover onto the wall control (Figure 25).

WALL
CONTROL

WALL CONTROL
COVER

12V BATTERY

HI

HI

MED

MED

LOW

LOW

FAN  OFF

EMERSON

U/L

D/L

LIGHT

Figure 25

BP7333 CF750 MAYA ZEN  12/22/06  7:59 AM  Page 13

Summary of Contents for MAYA ZEN CF750ORB00





















Reviews: