Emerson NELSON AXPTC125 Installation Instructions Manual Download

Page: 7 / 10

NELSON

™

INSTALLATION

AXPTC125 POWER TEE SPLICE CONNECTION KIT



INSTRUCTIONS

TULSA, OK 74146



TEL 918-627-5530



FAX 918-641-7336



www.nelsonheaters.com

GA-5052 Rev. 3 DRAFT

Sheet 7 of 10

August 2017



Terminate bus wires and ground braids to terminal

block.



Install enclosure cover.

STEP 9

FINAL ASSEMBLY



Install enclosure and secure to enclosure adapter

with supplied locknut.



Do not over tighten locknut



Enclosure may be rotated in 90° increments to

match installation requirements.

STEP 7

90°

Locknut

Cable Clamp



Install cable clamp over heating cables at top of

enclosure adapter.



Tighten cable clamp with supplied screws.



Do Not over tighten.

STEP 8

ELECTRICAL WIRING

Ground Braid

Terminal Blocks

Heater Cable

Ground Braid

Heater Cable

Summary of Contents for NELSON AXPTC125











Search results

Summary of Contents for NELSON AXPTC125

Reviews:

Related manuals for NELSON AXPTC125

Brands by name

Popular brands

Emerson NELSON AXPTC125, Installation Instructions Manual

Search results

Summary of Contents for NELSON AXPTC125

Reviews:

Related manuals for NELSON AXPTC125

Brands by name

Popular brands