Emerson Rosemount 5900C Reference Manual Download

Page: 237 / 322

6.6

Analog Input (AI) function block

Table 6-9

lists conditions reported in the BLOCK_ERR parameter. Conditions in bold type

are available for the Analog Input block. Conditions in

italics

are inactive for the AI block

and are given here only for your reference.

A block alarm will be generated whenever the BLOCK_ERR has an error bit set. Block error
types for the AI block are defined below in bold type.

Table 6-9: BLOCK_ERR Conditions

Condition
Number

Condition Name and Description

Other

Block Configuration Error

: the selected channel carries a measurement that is

incompatible with the engineering units selected in XD_SCALE, the L_TYPE
parameter is not configured, or CHANNEL = zero.

Link Configuration Error

Simulate Active

: Simulation is enabled and the block is using a simulated value in

its execution.

Local Override

Device Fault State Set

Device Needs Maintenance Soon

Input Failure/Process Variable has Bad Status

: The hardware is bad, or a bad

status is being simulated.

Output Failure

: The output is bad based primarily upon a bad input.

Memory Failure

Lost Static Data

Lost NV Data

Readback Check Failed

Device Needs Maintenance Now

Power Up

Out of Service

: The actual mode is out of service.

Reference Manual

Service and troubleshooting

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

237

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands

Emerson Rosemount 5900C, Reference Manual

Search results

Summary of Contents for Rosemount 5900C

Reviews:

Related manuals for Rosemount 5900C

Brands by name

Popular brands