manualshive.com logo in svg

Emerson Rosemount 5900C, Reference Manual

The Emerson Rosemount 5900C Reference Manual is a comprehensive and informative resource that users can download for free from our website. This manual provides detailed instructions and guidelines for effectively operating the Emerson Rosemount 5900C, ensuring users make the most of this high-quality product.

Share
Download
background image

Table C-17: Register Transducer Block Parameters

Index
Number

Parameter

Description

1

ST_REV

The revision level of the static data associated with
the function block. The revision value increments
each time a static parameter value in the block is
changed.

2

TAG_DESC

The user description of the intended application of
the block.

3

STRATEGY

The strategy field can be used to identify grouping of
blocks. This data is not checked or processed by the
block.

4

ALERT_KEY

The identification number of the plant unit. This
information may be used in the host for sorting
alarms, etc.

5

MODE_BLK

The actual, target, permitted, and normal modes of
the block. Target: The mode to “go to” Actual: The
mode the “block is currently in” Permitted: Allowed
modes that target may take on Normal: Most
common mode for target

6

BLOCK_ERR

This parameter reflects the error status associated
with the hardware or software components
associated with a block. It is a bit string, so that
multiple errors may be shown.

7

UPDATE_EVT

This alert is generated by any change to the static
data

8

BLOCK_ALM

The block alarm is used for all configuration,
hardware, connection failure or system problems in
the block. The cause of the alert is entered in the
subcode field. The first alert to become active will set
the Active status in the Status parameter. As soon as
the Unreported status is cleared by the alert
reporting task, another block alert may be reported
without clearing the Active status, if the subcode has
changed.

9

TRANSDUCER_DIRECTORY

Directory that specifies the number and starting
indices of the transducers in the transducer block.

10

TRANSDUCER_TYPE

Identifies the transducer.

11

TRANSDUCER_TYPE_VER

Transducer type version 

12

XD_ERROR

A transducer block alarm sub code.

13

COLLECTION_DIRECTORY

A directory that specifies the number, starting
indices, and DD Item ID’s of the data collections in
each transducer within a transducer block.

14

RB_PARAMETER

 

15-44

INP_REG_n_TYPE

Describes characteristics of input register n.
Indicates requested value is displayed as a floating
point (/ decimal) number.

F

OUNDATION

™

 Fieldbus Block Information

Reference Manual

September 2019

00809-0100-5901

312

Reference Manual

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900C

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Brand: ACS Pages: 56
Datavideo HS-600 Instruction Manual preview
HS-600
Brand: Datavideo Pages: 50
Waterous Eclipse Installation, Operation And Maintenance Manual preview
Eclipse
Brand: Waterous Pages: 90
Campbell SC105 Product Manual preview
SC105
Brand: Campbell Pages: 14
DARAY X200 Operating & Installation Manual preview
X200
Brand: DARAY Pages: 28
MacDon 3020 Operator'S Manual preview
3020
Brand: MacDon Pages: 88
Jiffy 56 Operating Manual/Parts Manual preview
56
Brand: Jiffy Pages: 15
Datalogic Matrix 400 Quick Reference Manual preview
Matrix 400
Brand: Datalogic Pages: 20
Datalogic Matrix 320 Product Reference Manual preview
Matrix 320
Brand: Datalogic Pages: 188
Gaspardo SP SPRINT Manual preview
SP SPRINT
Brand: Gaspardo Pages: 16
Gastrodomus PH100 Installation, Operating And Service Instructions preview
PH100
Brand: Gastrodomus Pages: 4
HANYOUNG NUX HL Series Instruction Manual preview
HL Series
Brand: HANYOUNG NUX Pages: 2
Gastrodomus CL Instructions For Use And Maintenance Manual preview
CL
Brand: Gastrodomus Pages: 39
RayLight HERA Technical Document preview
HERA
Brand: RayLight Pages: 34
Gazelle GAZELLE FREESTYLE User Manual preview
GAZELLE FREESTYLE
Brand: Gazelle Pages: 10
Latham ECLIPSE Installation Manual preview
ECLIPSE
Brand: Latham Pages: 19
Tascam SX-1 Brochure & Specs preview
SX-1
Brand: Tascam Pages: 8
Pari mini Instructions For Use Manual preview
mini
Brand: Pari Pages: 50

Brands by name

Popular brands

Load more brands