manualshive.com logo in svg

Emerson Rosemount 5900C, Reference Manual

The Emerson Rosemount 5900C Reference Manual is a comprehensive and informative resource that users can download for free from our website. This manual provides detailed instructions and guidelines for effectively operating the Emerson Rosemount 5900C, ensuring users make the most of this high-quality product.

Share
Download
background image

3.2

Installation considerations

When finding an appropriate location on the tank for a Rosemount 5900C Radar Level
Gauge, the conditions of the tank must be carefully considered. The Rosemount 5900C
should be installed so that the influence of disturbing objects is kept to a minimum,
preferably outside the radar signal beam.

Ensure that environmental conditions are within specified limits as listed in 

Specifications

and reference data

.

Ensure that the Rosemount 5900C Radar Level Gauge is installed such that it is not
exposed to higher pressure and temperature than specified in 

Specifications and reference

data

.

It is the responsibility of the user to ensure that the device meets the specific inside tank
installation requirements such as:

•

chemical compatibility of wetted materials

•

design/operation pressure and temperature

For a complete specification of the Rosemount 5900C device, you can identify the model
code on the attached antenna label and match with data in 

Ordering information

.

Do not install the Rosemount 5900C in non-intended applications, for example
environments where it may be exposed to extremely intense magnetic fields or extreme
weather conditions.

Antennas with plastic surfaces and painted surface, may under certain extreme conditions
generate an ignition-capable level of electrostatic charge. When installing in hazardous
areas ensure using tools, cleaning material etc. which can not generate electrostatic
charge.

3.2.1

Cone antenna requirements

When selecting cone antenna dimension, it is generally recommended to use as large
antenna diameter as possible. Standard cone antennas are available for 4-, 6- and 8-in.
tank openings. The 4-in. and 6-in. cones can be extended to fit long tank nozzles.

Table 3-1: Measuring Range for Cone Antenna

Antenna Size

Measuring Range

8-in.

0.8 to 20 m (2.6 to 65 ft).
(Possibility to measure 0.4 to 30 m (1.3 to 100 ft). Accuracy may be
reduced).

6-in.

0.8 to 20 m (2.6 to 65 ft).
(Possibility to measure 0.3 to 25 m (1 to 80 ft). Accuracy may be
reduced).

4-in.

0.8 to 15 m (2.6 to 50 ft).
(Possibility to measure 0.2 to 20 m (0.7 to 65 ft). Accuracy may be
reduced).

Reference Manual

Installation

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

29

Summary of Contents for Rosemount 5900C



































































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900C

Raven SC1 Accessory Installation Manual preview
SC1
Brand: Raven Pages: 27
Raven SC1 Calibration And Operation Manual preview
SC1
Brand: Raven Pages: 79
Raven SC1 Calibration & Operation Manual preview
SC1
Brand: Raven Pages: 88
DanMedical D-MAS HyperSat 2540 Instructions For Use Manual preview
D-MAS HyperSat 2540
Brand: DanMedical Pages: 103
Tascam CD-RW5000 Owner'S Manual preview
CD-RW5000
Brand: Tascam Pages: 27
Jay-Lor A50 Owner'S Manual preview
A50
Brand: Jay-Lor Pages: 72
MacDon TM100 Manual preview
TM100
Brand: MacDon Pages: 198
M-Triangel M1 Operating Instruction preview
M1
Brand: M-Triangel Pages: 6
1010music Toolbox Quick Start Manual preview
Toolbox
Brand: 1010music Pages: 2
1010music Blackbox Quick Start Manual preview
Blackbox
Brand: 1010music Pages: 4
JB Systems Sirius Operation Manual preview
Sirius
Brand: JB Systems Pages: 7
3B SCIENTIFIC PHYSICS 1023095 Instruction Sheet preview
1023095
Brand: 3B SCIENTIFIC PHYSICS Pages: 36
3A HEALTH CARE HAPPYNEB III Instruction Manual preview
HAPPYNEB III
Brand: 3A HEALTH CARE Pages: 16
360 Systems Short/cut 2000 Audio Editor Specification preview
Short/cut 2000 Audio Editor
Brand: 360 Systems Pages: 4
Daktronics Sportsound SSR-300 Operation Manual preview
Sportsound SSR-300
Brand: Daktronics Pages: 42
Eaton X10 Installation Manual preview
X10
Brand: Eaton Pages: 21
Eaton XV-152 Series Operating Instructions Manual preview
XV-152 Series
Brand: Eaton Pages: 70
NANO Pulsar Operating Instructions preview
Pulsar
Brand: NANO Pages: 4

Brands by name

Popular brands

Load more brands