Safety
Information
Introduction
Product
information
System
design
Mechanical
installation
Electrical
installation
Getting
started
Optimisation
Parameters
Technical
data
Component
sizing
Diagnostics
Unidrive SP Regen Installation Guide
161
Issue Number: 2 www.controltechniques.com
Indicates the version number of the data block. This is intended to be used when data blocks are used as drive macros. If a version number is to be
stored with a data block this parameter should be set to the required version number before the data is transferred. Each time Pr
11.37
is changed by
the user the drive puts the version number of the currently viewed data block in this parameter.
Gives the checksum of the data block or the bytes left on the card if Pr
11.37
= 1000.
Sets the timeout for the drive display to revert to status mode from edit mode following no key presses. Although this parameter can be set to less
than 2s, the minimum timeout is 2s.
* Modes 1 and 2 are not US (i.e. not saved when drive parameters are saved), mode 3 and 4 are US.
Therefore this parameter can only be saved to EEPROM if it has a value of 0, 3 or 4.
Reading (1)
Setting Pr
11.42
to 1 and resetting the drive will load the parameters from the card into the drive parameter set and the drive EEPROM. All
SMARTCARD trips apply. When the action is complete this parameter is automatically reset to zero. Parameters are saved to drive EEPROM after
this action is complete.
This operation is only performed if block 1 on the card is a complete copy of the EEPROM (i.e. types 1 to 5) and not a difference from default file. If
block 1 does not exist or the type is incorrect a C.typ trip occurs.
Programming (2)
Setting Pr
11.42
to 2 and resetting the drive will save the parameters in the drive EEPROM to a card, i.e. equivalent to writing 3001 to Pr
x.00
. All
SMARTCARD trips apply except C.Chg. If the data block already exists it is automatically over-written. When the action is complete this parameter is
automatically reset to zero.
Auto (3)
Changing Pr
11.42
to 3 and resetting the drive will save the complete parameter set from the EEPROM to the card. All SMARTCARD trips apply,
except C.Chg. If the data block already exists it is automatically overwritten.
If the card is removed when Pr
11.42
is set to 3 Pr
11.42
will be set to 0. If a card with a file 1 is inserted into a drive the drive must overwrite the file to
11.39
SMARTCARD data version
Drive mode
Regen
Coding
Bit
SP
FI
DE Txt VM DP
ND
RA NC NV PT US RW BU PS
1
1
1
Range
Regen
0 to 9,999
Default
Regen
0
Update rate
Background
11.40
SMARTCARD data checksum
Drive mode
Regen
Coding
Bit
SP
FI
DE Txt VM DP
ND
RA NC NV PT US RW BU PS
1
1
1
1
Range
Regen
0 to 65,335
Update rate
Background
11.41
Status mode time-out
Drive mode
Regen
Coding
Bit
SP
FI
DE Txt VM DP
ND
RA NC NV PT US RW BU PS
1
1
1
Range
Regen
0 to 250 s
Default
Regen
240
Update rate
Background
11.42
Parameter cloning
Drive mode
Regen
Coding
Bit
SP
FI
DE Txt VM DP
ND
RA NC NV PT US RW BU PS
1
1
*
1
1
Range
Regen
0 to 4
Default
Regen
0
Update rate
Background
NOTE
Summary of Contents for SP1201
Page 219: ......
Page 220: ...0471 0029 02 ...