Emerson Tartarini Dosaodor-D Instruction Manual Download

Page: 28 / 32

Parts List

Type Dosaodor-D (Figures 4 and 5)

The following items are provided for installation.

key Description

Part Number

Standard Wick Insert (not shown) or

M2006542X12

Extended Wick Insert (not shown)

M2007371X12

40 Odorant Filter

M4008542X12

41 Screw M8 x 16 (4 required) (not shown)

M5058026X12

The odorant filter should be installed between the

odorant storage tank and pneumatic panel per

Figures 4 and 5.
The filtering capacity of the odorant filter is 50 μm.

Type SA/2 Supply Filter (Figure 11)

key Description

Part Number

Elastomer Parts Kits (Order 1 kit for each Type SA/2)

(include keys: 6, 12, 13, 15 and 18)

Nitrile (NBR)

(standard)

GD89995X012

Fluorocarbon (FKM)

GD89995X022

Spring

Setpoint range: 43.5 to 72.5 psig / 3 to 5 bar

M0192560X12

Setpoint range: 8.7 to 21.7 psig / 0.6 to 1.5 bar

M0101230X12

Screw

M5058003X12

Washer

M0248490X12

Plate

M0174470X12

Regulator Seat

M0200830X12

6* O-ring

Nitrile (NBR)

(standard)

GD01001X032

Fluorocarbon (FKM)

GD01001X042

Body

M0297920X12

Filter Net

M0102200X12

Washer

M5057002X12

10 Nut

M5060005X12

11 Filter Cover

M0174411X12

12* Felt

GD10221X012

13* O-ring

Nitrile (NBR)

(standard)

GD01009X032

Fluorocarbon (FKM)

GD01009X042

14 Spring

M0105970X12

15* Pad Holder

Nitrile (NBR)

(standard)

GD23337X012

Fluorocarbon (FKM)

GD23337X022

17 Screw Unit

M0200790X12

18* Diaphragm

GD17446X012

19 Regulator Cover

M0239890X12

20 Spring Washer

M5001003X12

21 Locking Nut

M5006012X12

Pneumatic Panel (Figures 12 and 13)

key Description

Part Number

Panel

M0302140X12

Junction Box

M4009730X12

Ball Valve

M4006023X12

Three required for B1 version

Six required for B2 version

10 Level Switch and Float

See Table 5

11 Odorant Calibration Cylinder Junction Box

M0301510X12

12 Gauge

See Table 5

15 Relief Valve

See Table 5

19 Odorant Calibration Cylinder

See Table 5

22* Two Way Filling Solenoid Valve

M2007497X12

23 Needle Valve

M2007495X12

24 Type SA/2 Supply Regulator

(Nitrile (NBR) Elastomers)

[Setpoint range: 43.5 to 72.5 psig / 3 to 5 bar]

FSSA-1

31 Identification Label

34* Three Way Pressure/Depressure Solenoid Valve M4009297X12

38 Type SA/2 Supply Regulator,

(Nitrile (NBR) Elastomers)

[Setpoint range: 8.7 to 21.7 psig / 0.6 to 1.5 bar]

FSSA-5

39* Two Way Injection Solenoid Valve

M2007496X12

(Two required for B2 version)

Odorant Filter (Figure 9)

key Description

Part Number

Parts kit

(includes required quantities of

keys 40B, 40F and 40K)

M2201078X12

40A Plug

M0301870X12

40B O-ring 2118 for Odorant Filter

M6020174X12

40C Screw M8X130 TCEI (4 required)

M5058035X12

40D Upper Cover

M0301880X12

40E Cylinder Body

M0301900X12

40F Odorant Filter Cartridge

M0302500X12

40G Seal (2 required)

M6020085X12

40H Lower Cover

M0301890X12

40J Nut (4 required)

M5063006X12

40K O-ring 3056 for Odorant Filter (2 required) M6020180X12

*Recommended Spare Parts.

Type Dosaodor-D

Summary of Contents for Tartarini Dosaodor-D

































Search results

Summary of Contents for Tartarini Dosaodor-D

Reviews:

Related manuals for Tartarini Dosaodor-D

Brands by name

Popular brands

Emerson Tartarini Dosaodor-D, Instruction Manual

Search results

Summary of Contents for Tartarini Dosaodor-D

Reviews:

Related manuals for Tartarini Dosaodor-D

Brands by name

Popular brands