Trip
C.rtg
Value
186
Short description
Transfer of data between drives of different ratings detected
A parameter file has been transferred from a NV media card to the drive, but the current and/or voltage rating are different between source and target drive. This trip does not stop
the data transfer, but is a warning that the data for rating dependent parameters may not be the same on the target as the source drive. This trip also applies if a compare (using Pr
mm.000
set to 8yyy) is performed between a parameter file on the card on the drive.
Recommended actions:
Reset the drive to clear the trip.
This trip can be suppressed by setting Pr
mm.000
to 9666 and resetting the drive.
Trip
C.Typ
Value
187
Short description
Transfer of data between drives operating in different modes detected
This trip is produced during a compare if the drive mode in the file on the NV media card is different from the current drive mode and the file is a parameter file. This trip is
also produced if an attempt is made to transfer a parameter file where the source and target drive modes are different and the drive mode is outside the range allowed for the target
drive.
Recommended actions:
Ensure the destination drive supports the drive operating mode in the parameter file.
Clear the value in Pr
mm.000
and reset the drive.
Ensure destination drive operating mode is the same as the source parameter file.
Trip
cL.A1
Value
28
Short description
Current loop loss on analog input 1
Indicates that a current loss was detected in current mode on Analog Input 1. In 4-20mA and 20-4mA modes, loss of input is detected if the current falls below 3mA. See
Analog Input 1 Mode
(07.007) for further details.
Recommended actions:
Check control wiring is correct.
Check control wiring is undamaged.
Check
Analog Input 1 Mode
(07.007).
Check that the current signal is present and greater than 3mA
Trip
cL.A2
Value
29
Short description
Current loop loss on analog input 2
Indicates that a current loss was detected in current mode on Analog Input 2. In 4-20mA and 20-4mA modes, loss of input is detected if the current falls below 3mA. See
Analog Input 2 Mode
(07.011) for further details.
Recommended actions:
Check control wiring is correct.
Check control wiring is undamaged.
Check
Analog Input 2 Mode
(07.011).
Check that the current signal is present and greater than 3mA
Trip
CL.bt
Value
35
Short description
Control word trip (bit 12)
This trip is initiated by setting bit 12 on the control word in
Control Word
(06.042) when the control word is enabled (
Control Word Enable
(06.043) = On).
Recommended actions:
Check the value of
Control Word
(06.042).
Disable the control word in
Control Word Enable
(06.043).
Trip
Cur.c
Value
231
Short description
Current feedback calibration range error
Current calibration range error.
Recommended actions:
Hardware fault - contact the supplier of the drive.
Trip
D.Ch
Value
97
Short description
Drive has become active while data is being updated
A user action or a file system write is active that is changing the drive parameters and the drive has become active, i.e.
Drive Active
(10.002) = 1. The user actions that change drive
parameters are loading defaults, changing drive mode, or transferring data from an NV memory card to the drive. The file system actions that will cause this trip to be initiated if the
drive is enabled during the transfer are writing a parameter or macro file to the drive, or transferring a user program to the drive. It should be noted that none of these actions can be
started if the drive is active, and so the trip only occurs if the action is started and then the drive is enabled.
Recommended actions:
Ensure the drive is not enabled when one of the following is being carried out:
Loading defaults
Transferring user programs
250
Unidrive M200 Parameter Reference Guide
Issue: 01.05.00.10
Summary of Contents for unidrive m200
