Parameter
03.037
Frequency Output or PWM Output Scaling
Short description
Defines the scaling factor applied to the frequency or PWM output
Mode
Open
‑
loop
Minimum
0.000
Maximum
4.000
Default
1.000
Units
Type
16 Bit User Save
Update Rate
Background
Display Format
Standard
Decimal Places
3
Coding
RW, BU
Scale factor applied to the frequency or PWM output.
Parameter
03.038
Maximum Output Frequency
Short description
Defines the maximum frequency required at the frequency output
Mode
Open
‑
loop
Minimum
0
Maximum
3
Default
2
Units
kHz
Type
8 Bit User Save
Update Rate
Background
Display Format
Standard
Decimal Places
0
Coding
RW, TE, BU
Value
Text
Description
0
1
Fmax 1kHz
1
2
Fmax 2kHz
2
5
Fmax 5kHz
3
10
Fmax 10kHz
Defines the maximum frequency of the output for both frequency and PWM ouput modes as set by
Digital I/O 01 mode
(08.031). For frequency mode (
Digital I/O 01 mode
(08.031) = 2 ) the choice of
maximum output frequency depends on the requirement of the output. Due to limitations in the hardware, higher output frequencies do not offer the best resolution at the top end of the frequency range.
The table below indicates the resolution at the programmed maximum frequency:
Fmax (kHz)
Resolution at Fmax
1
14 bit
2
13 bit
5
12 bit
10
11 bit
Parameter
03.042
Frequency Input High Precision
Short description
Increase the frequency input measuring window
Mode
Open
‑
loop
Minimum
0
Maximum
1
Default
0
Units
Type
1 Bit User Save
Update Rate
Background
Display Format
Standard
Decimal Places
0
Coding
RW
This bit should be set to 1 if a higher accuracy is required than that defined in
Maximum Reference Frequency
(03.043). If
Frequency Input High Precision
(03.042) = 1 then the frequency input
measurement window is doubled. This doubles the accuracy of the frequency input measurment but increases the response time by two also.
If
Frequency Input High Precision
(03.042) = 0 then the frequency input measurement window is similar to Commander SK with better response time.
Parameter
03.043
Maximum Reference Frequency
Short description
Defines the maximum frequency expected at the frequency input
Mode
Open
‑
loop
Minimum
0.00
Maximum
100.00
Default
10.00
Units
kHz
Type
16 Bit User Save
Update Rate
Background
Display Format
Standard
Decimal Places
2
Coding
RW
Defines the maximum frequency expected at the frequency input. The time the frequency is measured over is defined by
Measurement Time = 2048 / Maximum reference frequency
With a maximum measurement time of 0.341 seconds.
2048 is used to give the measurement more stability. The output is 10 bits.
Maximum reference frequency of less than 6kHz will have a lower resolution.
Parameter
03.044
Frequency Reference Scaling
Short description
Defines the scaling factor applied to the frequency reference
Mode
Open
‑
loop
Minimum
0.000
Maximum
4.000
Default
1.000
Units
Type
16 Bit User Save
Update Rate
Background
Display Format
Standard
Decimal Places
3
Coding
RW, BU
Scale factor applied to the frequency reference.
Parameter
03.045
Frequency Reference
Short description
Displays the frequency reference
Mode
Open
‑
loop
Minimum
0.00
Maximum
100.00
Default
Units
%
Type
16 Bit Volatile
Update Rate
16ms
Display Format
Standard
Decimal Places
2
Coding
RO, FI, ND, NC, PT
Indicates the reference input if
Digital input 5 mode
(08.035) = 4.
The reference has a 16ms filter.
48
Unidrive M200 Parameter Reference Guide
Issue: 01.05.00.10
Summary of Contents for unidrive m200
