90
Unidrive M400 User Guide
Issue Number: 2
Maximum frequency
01.006
Menu 0 set-up
Menu 22
Minimum frequency
01.007 10.004
Motor map
05.006 05.007 05.008 05.009 05.010 05.011
Motor map 2
Menu 21
11.45
Motorized potentiometer
09.021 09.022 09.023 09.024 09.025 09.026 09.027 09.028 09.003
Offset reference
01.004 01.038 01.009
Onboard PLC
11.047 to 11.051
11.055
Open loop vector mode
05.014 05.017
Operating mode
11.031
05.014
Output
05.001 05.002 05.003 05.004
Over frequency threshold
03.008
Over modulation enable
05.020
PID controller
Menu 14
Positive logic
08.010
Power up parameter
11.022
Preset speeds
01.015
01.021 to 01.028
01.014 01.042
01.045 to 01.047
01.050
Programmable logic
Menu 9
Ramp (accel / decel) mode
02.004 02.008 06.001 02.002 02.003 10.030 10.031 10.039
Regenerating
10.010 10.011 10.030 10.031 06.001 02.004 02.002 10.012 10.039 10.040
Relay output
08.008 08.018 08.028
Reset
10.033
10.034 10.035 10.036 10.001
RFC mode (encoder less CLV
mode)
05.040
Scope
09.055 to 09.073
S ramp
02.006 02.007
Sample rates
05.018
SAFE TORQUE OFF input
08.039 08.040
Security code
11.030 11.044
Serial comms
11.023 to 11.027
Skip speeds
01.029 01.030 01.031 01.032 01.033 01.034 01.035
Slip compensation
05.027 05.008
NV media card
11.036 to 11.040
11.042
Firmware version
11.029 11.035
Frequency controller
03.010 to 03.017
Estimated frequency
03.002 03.003 03.004
Reference selection
01.014 01.015 01.049 01.050 01.001
Status word
10.040
Supply
05.005 06.046
Switching frequency
05.018 05.035 07.034 07.035
Thermal protection - drive
05.018 05.035 07.004 07.005
07.035 10.018
Thermal protection - motor
04.015 05.007 04.019 04.016 04.025
08.035
Thermistor input
08.035 07.047 07.050
Threshold detector 1
12.001
12.003 to 12.007
Threshold detector 2
12.002
12.023 to 12.027
Time - filter change
06.019 06.018 06.021 06.022 06.023
Time - powered up log
06.020
06.019 06.017 06.018
Time - run log
06.019 06.017 06.018
Torque
04.003 04.026 05.032
Torque mode
04.008 04.011
Trip detection
10.037 10.038
10.020 to 10.029
Trip log
10.020 to 10.029
10.041 to 10.060
10.070 to 10.079
Under voltage
05.005 10.016 10.015
V/F mode
05.015 05.014
Variable selector 1
12.008 to 12.016
Variable selector 2
12.028 to 12.036
Voltage controller
05.031
Voltage mode
05.014 05.017
05.015
Voltage rating
11.033 05.009 05.005
Voltage supply
06.046 05.005
Warning
10.019 10.012 10.017 10.018 10.040
Zero frequency indicator bit
03.005 10.003
Feature
Related parameters (Pr)
Summary of Contents for Unidrive M400
Page 197: ......
Page 198: ...0478 0044 02 ...