background image

 

1592028040 XWEB300D_500D_PRO STP GB r1.0 25.11.2020.doc 

XWEB PRO 

 9/20 

 

 
ATTENTION

: the status of the System LED is linked to that of the corresponding "System alarm" relay 

 

ATTENTION

: for XWEB300D the 'relay system' as AUX assumes the following logic: 

• at rest (XWEB off) contacts 30 and 32 are closed 

• in the event of an alarm, it closes at 30-31 
• when switched on, it closes for a few seconds at 30-31. then if there are no alarms it returns to res t and  
closes at 30-32. 
 

ATTENTION

: always use the power supply of the external modem f rom t he X WEB  its elf  t o ensure t he 

correct sending of messages (for example SMS). In other words, use the cable supplied in t he modem K IT 
on terminals 33-34. 
 

ATTENTION

: the 'reset modem' relay is energized for reset, in conditions of non-use every two minutes; and 

bef ore each activation of the service. It is necessary to insert this relay in the p ower s upply  circuit  of  t he 
external modem to ensure the correct sending of messages (SMS). 
 

ATTENTION

:  During  the  initial  start-up phase, the STATUS, REC and ALARM LEDs FLASH at regular 

intervals. This flashing IS NORMAL and highlights the regular progress of the ignition phase which can las t 
up to 5 minutes. 
 
 

 
 
 
 

 

 

Avoid  direct  passage  between  operators  as  much  as   possible  (to  avoid  electrostatic 
induction  and subsequent discharges); 

 

If  the  electrical  voltage  supply  differs  from  the  required  rating,  this  could  seriously damage 
the system; 

 

Connection errors (and connections that differ from the prescribed ones) can  pose a danger 
to  operator safety and cause  faults in the system and to the instruments that are connected 
to it; 

 

Insert  one  or  more  easily  accessible  disconnecting  devices  to  the  exterior of the device to 
separate the device from the power mains;

 

 

Do not use the device in environments with  flammable  gases. 

 

Do not modify  the device in any way.

 

 
 

Summary of Contents for XWEB300D





















Reviews: