background image

February 1999

Y690VB Series

Instruction Manual
Form 5465

D102594X012

www.FISHERregulators.com

Y690VB Series Vacuum Breakers

Introduction

Scope of Manual

This manual describes and provides instructions and
parts lists for the Type Y690VB and the Type Y690VBM
vacuum breakers. Instructions and parts lists for other
equipment used with these breakers are found in
separate manuals.

Product Description

The Y690VB Series vacuum breakers are used for
precise control of small capacity, low-pressure service
applications where an increase in vacuum must be
limited. These direct-operated vacuum breakers come
in 3/4 (DN 20) and 1-inch (DN 25) body sizes and have
a 1/4-inch (6,4 mm) or 1/2-inch (12,7 mm) orifice. The
individual products are described as follows:

Type Y690VB

The Type Y690VB is a vacuum breaker with internal
pressure registration requiring no downstream
control line.

Installation

Personal injury, property damage, equip-
ment damage, or leakage due to escaping
gas or bursting of pressure-containing
parts may result if this equipment is over-
pressured or is installed where service
conditions could exceed the limits given in
table 1, or where conditions exceed any
ratings of the adjacent piping or piping
connections. To avoid such injury or
damage, provide pressure-relieving or
pressure-limiting devices (as required by
the appropriate code, regulation, or stan-
dard) to prevent service conditions from
exceeding those limits. Additionally,
physical damage to this equipment could
cause personal injury or property damage
due to escaping gas. To avoid such injury
or damage, install the equipment in a safe
and well ventilated location.

Equipment operation within ratings does not preclude
the possibility of damage from debris in the lines or
from external sources. This equipment should be
inspected for damage periodically and after any over-
pressure condition.

WARNING

!!!!!

Figure 1.  Type Y690VB Vacuum Breaker

W7292

Type Y690VBM

The Type Y690VBM is a vacuum breaker with a control
line connection and a throat seal for external pressure
registration.

Specifications

Table 1 gives some general ratings and specifications
for the Y690VB Series vacuum breakers. Individual
breakers come from the factory with the specific data
stamped on the nameplate.

Summary of Contents for Y690VB Series













Reviews: