background image

Y690VB Series

Fisher is a mark owned by Fisher Controls International, Inc., a business of Emerson Process Management.  The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the
property of their respective owners.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express
or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.

Fisher does not assume responsibility for the selection, use or maintenance of any product.  Responsibility for proper selection, use and maintenance of any Fisher product remains solely with the purchaser.

For information, contact Fisher:

Marshalltown, Iowa 50158 USA
McKinney, Texas 75070 USA
28320 Gallardon, France
40013 Castel Maggiore (BO), Italy
Sao Paulo 05424 Brazil
Singapore 128461

www.FISHERregulators.com

 ©Fisher Controls International, Inc.,  1999;  All Rights Reserved

Summary of Contents for Y690VB Series













Reviews: