background image

ZX Platform Condensing Unit

 

2

Figure 03.

 

ZX Platform CDU Features

Standard Unit Features

  Pre-painted enclosures for corrosion protection.

   Heavy duty steel base with 23 mm raised legs.

   Brass service valves located externally for 

easy access.

   Raised electrical access panel for easier 

serviceability.

   Receivers with fusible plug, liquid shut-off valve 

and charging port.

   Easy to read moisture indicator.

   Variable-speed PSC fan motors.

  Advanced performance alert diagnostics.

   Over-sized condenser coils with additional fin 

corrosion protection for coastal zones.

   Light weight, slim-line profile for maneuverability 

and ease of installation.

   All units are factory tested for braze joint leaks, 

wiring connections, electrical continuity and start-

up performance.

   Oil separator and accumulator standard on low 

temperature models.

   Operating ambient is 48°C  to -23°C*.

Proprietary Electronic Algorithms to Control Fan 
Speed, Optimizing Energy Performance for Local 
Seasonal Ambient Temperatures

Copeland Scroll 
Compressor Technology

• High Efficiency
• Ultra Quiet
• High Reliability

Variable Speed PSC
Fan Motors

• High Efficiency
• Ultra Quiet
• Optimizes Air-

Flow

  for Maximum 
     Heat Transfer

Oversized Condenser Coil 
for Maximum Heat Transfer

 Compressor Reverse Rotation

 Compressor Over Current

 Compressor Internal Motor Protector Trip

 Discharge Gas Over Heat

 High Pressure Cut Out

 Low Pressure Cut Out (only on MT series)

 Refrigerant Flood Back

 Compressor Minimum Off Time

 Internal Thermal Sensor Failure

Diagnostic 

Digital 

Messaging

Built-in ZX Platform 

Controller

- Shuts down unit during failure
- With real time monitoring of 

compressor operating conditions

ZXD Series

ZX and ZXL Series

Diagnostic Protection

Increased Reliability and Lower Maintenance 

Costs

Flexibility

More Installation Options

Highest Efficiency

Lower Energy Bills

Summary of Contents for ZX Platform Condensing Unit





















































Reviews: