background image

E-mail: emi@enviromaster.com

Made in Rome, New York, USA

2

SAFETY INSTRUCTIONS

 

Read all instructions before using the EMI Air han-

dler.  Install or locate this unit only in accordance with 

these instructions.  Use this unit only for its intended 

purpose as described in this manual.

 

Check the rating plate on the EMI air han-

dler before installation to make certain the 

voltage shown is the same as the electrical 

supply to the unit. Installing a unit with the 

wrong Voltage may void the warranty!

 The EMI Air handler must be connected to a 

properly grounded electrical supply.  Do not fail 

to properly ground this unit.

 Turn off the electrical supply before servicing the 

EMI Air handler.

 Do not use the EMI Air handler if it has damaged 

wiring,  is  not  working  properly,  or  has  been 

damaged or dropped.

[Save these instructions]

!  

!  

WARNING

!  

Recognize this symbol as an indication 

of Important Safety Information.

!  

INSTAllATION, OpERATION, ANd MAINTENANCE MANUAl

 

P/N# 240004373, Rev. A [1/09]

 

This manual is intended as an aid to qualified service 

personnel  for  proper  installation,  operation,  and  main-

tenance  of  the  EMI  wall  or  ceiling  mounted  air  handler.  

Read  these  instructions  thoroughly  and  carefully  before 

attempting installation or operation.  Failure to follow these 

instructions may result in improper installation, operation, 

service or maintenance, possibly resulting in fire, electrical 

shock, property damage, personal injury, or death.

TO THE INSTAllER

(1)  Retain  this  manual  and  warranty  for  future  refer-

ence.

(2) Before leaving the premises, review this manual to    

be sure the unit has been installed correctly and run 

the unit for one complete cycle to make sure it func-

tions properly.
 

To  obtain  technical  service  or  warranty  as-

sistance during or after the installation of any EMI 

unit, check  our  website @ www.enviromaster.com 

or call  your installing contractor or distributor. Our 

technical service department may be contacted at 

1-800-228-9364.

 

When  calling  for  assistance,  please  have 

the following information ready:

• Model number _____________________

• Serial number  _____________________

• Date of installation  _________________

EMI dUCTlESS CHIll WATER AIR HANdlERS

 

Shipping Damage MUST be Reported to the Carrier IMMEDIaTELY!!!

Examine the exterior. Remove cover and examine compressor and piping for signs of damage. 

Common To All Air Handlers

..

1-7

 

c

ontinued 21-32

Safety Instructions .................................................. 2

The EMI Air handler Family  ....................................3

Installer Supplied Items ...........................................3

Items for Consideration ............................................4

Controls and Components  ......................................4

Optional Controls/Components  ...............................4

high Volt Electrical Wiring  .......................................4

Low Volt Electrical Wiring  ....................................5-6

Dip Switch Settings ..................................................6

Ceiling Mounted Air handler CCP  ........................7-8

Wall Mounted Air handler WCP  .........................9-11

Preperation for Start-up  ........................................12

Unit Mount Control Start-Up  ............................13-15

Wall Thermostat Start-Up  ................................15-16

Test Unit Performance Data  ..................................17

Maintenance and Troubleshooting  ...................18-20

Warranty  ...............................................................21

TABlE OF CONTENTS

Specific Unit Installation

Summary of Contents for ComfortWave CCP Series





















Reviews: