Empava EMPV-24WO08 User Operating Instructions Manual Download

Page: 1 / 22

• USERS OPERATING INSTRUCTIONS

• INSTALLATION ADVICE

•

IMPORTANT - PLEASE READ AND FOLLOW

• Before beginning, please read these instructions completely and carefully.

• Do not remove permanently affixed labels, warnings, or plates from the product. This

may void the warranty.

• Please observe all local and national codes and ordinances.

• Please ensure that this product is properly grounded.

• The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

• The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel

Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance

with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN

CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National

Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.

Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical

Codes Part 1 and/or local codes.

B U I L T - I N G A S O V E N

for residential use only

Model:

EMPV-24WO08/EMPV-24WO09

Stainless steel models only: This built-in oven is supplied with a protective film on

steel and aluminium parts. This film must be removed before installing/using the

appliance.

Summary of Contents for EMPV-24WO08























Search results

Summary of Contents for EMPV-24WO08

Reviews:

Related manuals for EMPV-24WO08

Brands by name

Popular brands

Empava EMPV-24WO08, User Operating Instructions Manual

Search results

Summary of Contents for EMPV-24WO08

Reviews:

Related manuals for EMPV-24WO08

Brands by name

Popular brands