Empire Comfort Systems DVCC32BP30N-2 Installation Instructions And Owner'S Manual Download

Page: 34 / 56

35919-4-1015

Page 34

STANDING PILOT OPERATING INSTRUCTIONS

REMOTE/OFF/ON Switch

The fireplace is equipped with a

REMOTE/OFF/ON switch. A wire

harness is attached to the REMOTE/OFF/ON switch. The red,

black and green (wires) female push-ons attach to the REMOTE/

OFF/ON switch. At the opposite end of the wire harness, the black

and green (wires) female push-ons attach to the gas valve. An ad-

ditional green wire and the red wire, which are stripped and bare,

will attach to one of the accessories that can be purchased for use

with your fireplace.

Operation of REMOTE/OFF/ON Switch with no Accessories

To ignite main burner, turn the control knob on the gas valve from

the PILOT position to the ON position. Turn the REMOTE/OFF/ON

switch from the OFF position to the ON position. The additional

green wire and red wire, which are stripped and bare are not used.

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the REMOTE/

OFF/ON switch wire harness to the wall switch. Turn the REMOTE/

OFF/ON switch to the REMOTE position. Pivot the rocker switch

on the FWS-1 to the ON position.

Wall Thermostats (optional)

TRW - Wireless for Millivolt models

TMV - Reed switch for Millivolt models

Battery Operated Remote Controls, FRBC, FRBTC, and TRW

Connect the green and red, stripped and bare, wires on the

REMOTE/OFF/ON switch wire harness to the remote receiver

that is a component in the remote kit. Turn the REMOTE/OFF/ON

switch to the REMOTE position. Follow instructions included with

the remote to complete installation.

Note:

If batteries fail in the remote, and immediate heat is desired,

turn the REMOTE/OFF/ON switch from the REMOTE position to

the ON position.

Installation of Remote Receiver

Place remote receiver on the floor of fireplace behind the louver as

far forward as possible.

Attention:

The Velcro loop and hook are not necessary in this

installation but can be used to secure remote receiver.

Refer to remote control installation and operating instructions for

more details on remote control.

Millivolt Control

The valve regulator controls the burner pressure which should be

checked at the pressure test point. Turn captured screw counter

clockwise 2 or 3 turns and then place tubing to pressure gauge over

test point (Use test point “A” closest to control knob). After taking

pressure reading, be sure and turn captured screw clockwise firmly

to re-seal. Do not over torque. Check for gas leaks.

Millivolt thermopile is self generating. Gas valve does not require

24 volts or 110 volts.

Check System Operation

Millivolt system and all individual components may be checked with

a millivolt meter 0-1000 MV range.

Use wire of a gauge proper for the length of the wire:

Recommended Wire Gauges

Maximum Length

Wire Gauge

1-ft to 10-ft

10-ft to 25-ft

25-ft to 35-ft

Millivolt System

The standing pilot burns continuously even when the main burner

is OFF.

When you ignite the pilot, the thermopile produces millivolts (electrical

current) which energizes the magnet in the gas valve. After 30

seconds you can release the gas control knob and the pilot will stay

ON. Allow the pilot flame to burn an additional one to two minutes

before you turn the gas control knob from the PILOT position to

the ON position. This allows the millivolts current to build-up to a

sufficient level to operate the gas control properly.

1. Follow the SAFETY and LIGHTING INSTRUCTIONS for

standing pilot controls found in this manual and on labels found

in control compartment behind the door assembly.

CAUTION

During the initial purging and subsequent lightings, never

allow the gas valve control knob to remain depressed in the

“pilot” position without pushing the piezo ignitor button at

least once every second.

2. During the operating season, leave the control valve knob in

the “ON” position. This will allow the pilot flame to remain lit.

Turn the burner flame on or off with the fireplace

REMOTE/

OFF/ON switch, wall switch or remote controls.

NOTE:

The gas control valve allows you to increase or decrease the

height of the main burner flame. The control valve has a pressure

regulator with a knob as shown in

Figure 68.

Rotate the knob

clockwise to “HI” to increase the flame height and counterclockwise

to “LO” to decrease the flame height.

3. When the heating season ends, turn the REMOTE/OFF/ON

switch to “OFF” and the control valve to “OFF”. The system,

including the pilot light, will be shut down.

Figure 68

The OWNER should carefully read and follow these operating

instructions.

Initial Lighting

Lower the door assembly to view the gas controls for the fireplace.

Upon completing the gas line or turning the gas valve on after it has

been in the “OFF” position, a small amount of air will be in the lines.

When first lighting the fireplace, it will take a few minutes for the

lines to purge this air. Once the purging is complete, the fireplace

will light and operate satisfactorily.

Subsequent lightings of the appliance will not require purging if the

gas valve is not turned to “OFF.”

Pilot Flame

The pilot flame should cover the thermopile and thermocouple.

THERMOPILE

PILOT

THERMOCOUPLE

Figure 69

MILLIVOLT OPERATING INSTRUCTIONS (BP3 SERIES)

Summary of Contents for DVCC32BP30N-2

























































Search results

Summary of Contents for DVCC32BP30N-2

Reviews:

Related manuals for DVCC32BP30N-2

Brands by name

Popular brands

Empire Comfort Systems DVCC32BP30N-2, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for DVCC32BP30N-2

Reviews:

Related manuals for DVCC32BP30N-2

Brands by name

Popular brands