Empire Comfort Systems DVCD32FP30N-1 Owner'S Manual Download

Page: 53 / 60

28365-2-0811

Page 53

Attention

: Install blower assembly before connecting gas inlet

supply line

Note

: Junction box on right side of fireplace must be pre-wired at

time of fireplace installation for use with blower assembly.

It is recommended that an ON/OFF wall switch be installed

that will activate the power supply to the furnace by a

qualified electrician.

1. If installed, turn OFF gas supply to fireplace.

2. If applicable, turn OFF electric supply to fireplace.

3. Lower bottom louver on fireplace.

4. Refer to page 55, "Junction Box Wiring Installation Instructions"

to complete wiring of junction box.

Attention

: If installed, do not damage gas inlet supply line

when blower assembly is inserted into fireplace. If

necessary, remove gas inlet supply line.

5. Insert blower assembly into interior, bottom of fireplace.

Position blower assembly behind gas valve, align notch

on back of blower assembly with center screw on fireplace

back and push blower assembly against fireplace back. The

magnets on the back and bottom of blower assembly will

sufficiently hold blower assembly in place.

6. Position speed control box to the right of gas valve. Attach

speed control box to bottom of fireplace. The magnets on

bottom of speed control box will sufficiently hold speed control

box in place.

7. With base (flush face) of fan control switch facing upward,

insert base of fan control switch under the mounting tabs on

valve bracket. The base (flush face) of fan control switch must

be in contact with bottom of firebox.

8. Insert power cord plug into junction box.

9. Close bottom louver on fireplace.

10. Installation of FBB4 optional variable speed blower assembly

is completed.

Wiring

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the

National Electrical Code, ANSI/NFPA 70

, if an external

electrical source is utilized.

This appliance is equipped with

a three-prong [grounding] plug for your protection against

shock hazard and should be plugged directly into a properly

grounded three-prong receptacle. Do not cut or remove the

grounding prong from this plug.

For an ungrounded receptacle,

an adapter, which has two prongs and a wire for grounding, can

be purchased, plugged into the ungrounded receptacle and its

wire connected to the receptacle mounting screw. With this wire

completing the ground, the appliance cord plug can be plugged

into the adapter and be electrically grounded.

Caution: Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper

and dangerous operation. Verify proper operation after

servicing.

Blower Motor

The blower motor does not have oiling holes. Do not attempt to

oil the blower motor.

Blower Wheels

The blower wheels will collect lint and could require periodic

cleaning. If the air output decreases or the noise level increases,

it indicates a dirty blower wheel. Remove fan and clean blower

wheels.

Warning: Unplugging of blower accessory will not stop the

heater from cycling. To turn off gas to the heater (millivolt

model): push in gas control knob slightly and turn clockwise

to "OFF." Do not force. To turn off gas on direct ignition

model, turn gas line valve to "OFF."

Note: Refer to wiring instructions on page 54 for proper

operation.

JUNCTION BOX

SEE NOTE

VALVE BRACKET

FAN SWITCH

SPEED CONTROL

SWITCH HOLDER

(TOP OF VALVE BRACKET)

FAN KIT

FBB4 OpTIONAL VARIABLE SpEED BLOWER INSTALLATION

Summary of Contents for DVCD32FP30N-1





























































Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands

Empire Comfort Systems DVCD32FP30N-1, Owner'S Manual

Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands