Empire Comfort Systems DVCD32FP30N-1 Owner'S Manual Download

Page: 6 / 60

28365-2-0811

Page 6

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner fill out and mail warranty card

supplied with the fireplace.

3. Installer should show owner how to start and operate the

fireplace.

This direct vent gas fireplace heater is designed to operate

with all combustion air being siphoned from the outside of the

building and all exhaust gases expelled to the outside of the

building. The information contained in this manual pertains

to all models and gas control systems unless otherwise

noted.

Appliance Certification

This fireplace is design certified in accordance with American

National Standard/CSA Standard ANSI Z21.88/CSA 2.33

and by Underwriters Laboratories as a Direct Vent Gas

Fireplace Heater and shall be installed according to these

instructions.

Consult your local building code agency, prior to installation,

to ensure compliance with local codes-including permits and

inspections.

The fireplace, when installed, must be electrically grounded

in accordance with local codes or, in absence of local codes,

with the

National Electric Code ANSI/NFPA 70

or Canadian

Electric code, CSA C22.1, if an external electrical source is

utilized.

These models may be installed in a bedroom or bed-sitting

room in the U.S.A. and Canada.

Qualified Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of

equipment shall be performed only by a qualified agency.

The term “qualified agency” means any individual, firm,

corporation or company which either in person or through

a representative is engaged in and is responsible for (a)

the installation or replacement of gas piping or (b) the

connection, installation, repair or servicing of equipment,

who is experienced in such work, familiar with all precautions

required and has complied with all the requirements of the

authority having jurisdiction.

The installation must conform with local codes or, in the

absence of local codes, with the

National Fuel Gas Code ANSI

Z223.1/NFPA 54* Natural Gas and Propane Installation Code,

or CSA B149.1 in Canada.

*Available from the American National

Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10036.

Any alteration of the original design, installed other than

as shown in these instructions or use with a type of gas

not shown on the rating plate is the responsibility of the

person and company making the change.

Important

All correspondence should refer to complete Model Number,

Serial Number and type of gas.

High Altitude

When installing this unit at an elevation above 2000 feet (in

the United States) it may be necessary to decrease the input

rating by changing the existing burner orifice to a smaller size.

Generally, input should be reduced 4 percent for each 1000

feet above sea level. However, if the heating value of the gas

has been reduced, this general rule may not apply. Check

with local gas utility for proper orifice size identification.

Canadian High Altitude

Altitude: 0-4500 feet (0-1370 m)

When installing this unit at an elevation above 4500 feet (in

Canada), check with local authorities.

Consult your local gas utility for assistance in determining

the proper orifice for location.

preparation

This direct vent gas fireplace and its components are tested

and safe when installed in accordance with this Installation

Manual. Report to your dealer any parts damaged in shipment,

specifically check glass condition. Do not install unit with

damaged, incomplete, or substitute parts. Read all instructions

before starting installation and follow these instructions

carefully during installation to insure maximum benefit and

safety. Failure to follow them will void your warranty and may

present a fire hazard.

The warranty will be voided by, and the warranter disclaims

any responsibility for the following actions:

• Installation of any damaged fireplace or vent system

component.

• Modification of the fireplace or direct vent system.

• Installation other than as instructed by Empire Comfort

Systems, Inc.

• Improper positioning of the logs, glass door or decorative

rock.

• Installation and/or use of any component part not

manufactured or approved by manufacturer.

INTRODUCTION

Warning: This unit is not for use with solid fuels.

State of Massachusetts:

The installation must be made

by a licensed plumber or gas fitter in the Commonwealth

of Massachusetts.

Warning

: ANY CHANGE TO THIS FIREPLACE OR ITS

CONTROLS CAN BE DANGEROUS.

Improper installation or use of the fireplace can cause

serious injury or death from fire, burns, explosions, or

carbon monoxide poisoning.

Summary of Contents for DVCD32FP30N-1





























































Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands

Empire Comfort Systems DVCD32FP30N-1, Owner'S Manual

Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands