background image

12434-7-0706

Page 1

DIRECT  VENT 

WALL  FURNACE

MODELS

DV-25-2SG 

DV-35-2SG

EFFECTIVE  DATE 

JULY 2006

WARNING:  If  not  installed,  operated  and 

maintained in accordance with the manufacturer's 

instructions,  this  product  could  expose  you  to 

substances in fuel or from fuel combustion which 

can cause death or serious illness.

INSTALLATION  INSTRUCTIONS

AND

OWNER'S  MANUAL

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only)  or  mobile  home,  where  not  prohibited  by 

state or local codes.
This appliance is only for use with the type of gas 

indicated  on  the  rating  plate.  This  appliance  is 

not convertible for use with other gases, unless a 

certified kit is used.

Installer:  Leave  these  instructions  with  the 

consumer.

Consumer:  Retain  these  instructions  for  future 

use.

— Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or 

any other appliance.

 —  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Immediately  call  your  gas  supplier 

from a neighbor's phone.  Follow the 

gas supplier's instructions.

•  If you cannot reach your gas supplier, 

call the fire department. 

 —  Installation and service must be performed 

by a qualified installer, service agency or 

the gas supplier.

WARNING:  If the information in this manual 

is not followed exactly, a fire or explosion may 

result causing property damage, personal injury 

or loss of life.

Summary of Contents for DV-25-2SG





















Reviews: