background image

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

WARNING:  If  not  installed,  operated 

and  maintained  in  accordance  with  the 

manufacturer's instructions, this product could 

expose you to substances in fuel or from fuel 

combustion which can cause death or serious 

illness.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only) or mobile home, where not prohibited by 

state or local codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless 

a certified kit is used.

Installer:  Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

—  Do not store or use gasoline or other flamma

-

ble vapors and liquids in the vicinity of this or 

any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s  phone.  Follow  the  gas  suppli-

er’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal 

injury or loss of life.

DIRECT  VENT 

WALL  FURNACE

MODELS

DV-25T-1

DV-35T-1

Summary of Contents for DV-25T-1





















Reviews: