background image

INSTALLATION INSTRUCTIONS 

AND

OWNER´S MANUAL

GRAVITY DIRECT VENT 

WALL FURNACE

EFFECTIVE DATE

APRIL, 2003

WARNING: If the information in 
these instructions are not followed 
exactly, a fire or explosion may result 
causing property damage, personal 
injury or loss of life.

— Do not store or use gasoline or other 

flammable vapors and liquids in the 
vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do 
not use any phone in your building.

Immediately call your gas supplier 
from a neighbor's phone. Follow the 
gas supplier's instructions.

If you cannot reach your gas supplier, 

call the fire department.

— Installation and service must be 

performed by a qualified installer, 
service agency or the gas supplier.

• 
• 

• 

• 

This appliance is only for use with the 
type of gas indicated on the rating plate. 
This appliance is not convertible for use 
with other gases, unless a certified kit is 
used.

WARNING: If not installed, operated 
and maintained in accordance with the 
manufacturer's instructions, this product 
could expose you to substances in fuel or 
from fuel combustion which can cause 
death or serious illness.

MODELS

MV 120
MV 130
MV 145

Page 1

MV1XX-1-0603

Summary of Contents for MV 120

















Reviews: