background image

8

 

 SAFETY INSTRUCTIONS FOR CORDLESS SANDER 

flammable, but they also obstruct vents under the charger.

 

This product is not a toy. Keep it out of reach of children.

People  with  pacemakers  should  consult  their  physician(s)  before

use.  Electromagnetic  fields  in  close  proximity  to  heart  pacemaker

could cause pacemaker interference or pacemaker failure.

In addition, people with pacemakers should:

Avoid operating alone.

Do not use with power switch locked on.

Properly maintain and inspect to avoid electrical shock.

Properly ground power cord. Ground Fault Circuit Interrupter

(GFCI)  should  also  be  implemented

as it  prevents  sustained

electrical shock.

The  warnings,  precautions,  and  instructions  discussed  in  this

instruction  manual  cannot  cover  all  possible  conditions  and

situations  that  may  occur.  It  must  be  understood  by  the  operator

that  common  sense  and  caution  are  factors  which  cannot  be  built

into this product but must be supplied by the operator.

 SPECIFICATIONS 

Voltage: 24V Max

 

NO Load Speed: 11000RPM 

Pad Size: 5-1/2"x5-1/2"x3-1/8" 

Switch Type: Dust Resistant 

Battery Type: Li-ion

 

Charging Time: 1-2Hours

 

Includes:

 

1 pc 24V Cordless mouse sander

 

1 pc 24V Lithium-ion battery(2000mAh) 

1 pc Charger

 

1 pc Dust collection box 

10 pcs Sanding paper  

1 pc Instruction manual

 

Summary of Contents for CDS326



















Reviews: