background image

Auto Modes

 

The auto modes react to the audio coming in and modify the 
attack and release in real-time depending on what the music's 
doing.  In each auto mode, there are 2 detectors that run in 
parallel.  One with really fast time constants at a higher 
threshold that reacts primarily to peaks, and a slower detector, 
with a lower threshold to smooth the overall signal.  There is 
also some frequency compensation in these detectors which 
changes the ratio slightly depending on frequency.  This allows 
the auto modes to provide extremely transparent compression 
that isn't possible with traditional attack and release controls. 

Auto mode 1 : 

This mode is great for general dynamic control. It 

can be used while tracking vocals to control peaks and smooth 
out the overall level, without nasty artifacts. Also, it works great 
for sitting things in a dense mix, but still allowing them to 
breathe. 

Auto mode 2 : 

This is great on acoustic guitar.  The attack is 

more open and it makes things sound big and present without 
squashing the transients too much.  On individual sources it's 
good for bringing them forward in a mix and even works well on 
a mix buss to add some overall punch.

 

 

Summary of Contents for ECM-519













Reviews: