background image

Hardware Reference

Dec

l

aration of Conformity

Note

Changes or modifications not expressly approved by Emulex
Corporation could void the user's authority to operate this
equipment.

DECLARATION OF CONFORMITY

Manufacturer: Emulex Corporation

3535 Harbor Blvd.
Costa Mesa, CA 92626
USA

declares under sole responsibility that the product:

Product
Name:

LightPulse™ LP8000 Fibre Channel PCI Host Adapter

Assembly
Number:

FC1020017−XX (GBIC model)
FC1020016−XX (embedded optical, 1x9 model)

Accessories:

Emulex PN 2300029 (Active Copper DB9 GBIC Module)
Emulex PN 2300028 (Shortwave Optical GBIC Module)
Emulex PN 2300030 (Longwave Optical GBIC Module)

to which this declaration relates is in conformity with the following
standards or other documents:

Safety:

IEC950:1991+A1,A2/EN60950 (1992)+ A1,A2
including EN60825−1 (1994)
TUV Rheinland, Certificate No. R9677151.1

EMC:

EN55022 (1994)/CISPR−22 (1993), Class A
EN50082−1 (1997)

following the provisions of the Low
Voltage Directive 73/23/EEC and EMC
Directive 89/336/EEC (as amended by 92/31/EEC) and is Marked in
accordance with the CE Marking Directive 93/68/EEC

 February 18, 1999
Costa Mesa, CA

European Contact: Emulex Corporation

7 & 8 Forrest Court
Oaklands Park
Fishponds Road
Wokingham, Berkshire
RG41 2FD, England

Telephone:
44−118−977−2929
Fax: 44−118−977−3237

Emulex Drivers, Software and Manuals

17

Summary of Contents for LP8000


























Reviews: