manualshive.com logo in svg

Encom ENC-900, Operating Manual

The Encom ENC-900 is a high-performance device designed to enhance productivity. Seamlessly navigate through its advanced features with the help of the comprehensive Operating Manual available for free download at 88.208.23.73:8080. This manual is your go-to resource for maximizing the potential of your Encom ENC-900.

Share
Download
background image

 

900 MHz 

Spread-Spectrum OEM 
Radio Modem

 

 

 
 

WARNING 
 
In order to comply with the FCC/IC 
adopted RF exposure requirements, this 
transmitter system will only be installed 
according to manufacturer’s Installation 
Guidelines. Installation of all antennas must 
be performed in a manner that will provide 
at least 20cm clearance from the front 
radiating aperture, to any user or member 
of the public. 
 
 
 
EQUIPMENT LABELING 
 
The manufacturer, product name, and FCC 
and Industry Canada identifiers of this 
product must appear on the outside label of 
the end-user equipment. 

 

This manual contains information of proprietary
interest to Encom Wireless Data Solutions Inc.  It 
has been supplied in confidence to purchasers and 
users of the 

ENC-900,

and by accepting this material 

the recipient agrees that the contents will not be
copied or reproduced, in whole or in part, without
prior written consent of Encom Wireless Data
Solutions Inc. 
Encom Wireless Data Solutions Inc. has made every 
effort to assure that this document is accurate and
complete.  However, the company reserves the right
to make changes or enhancements to the manual
and/or the product described herein at any time and
without notice.  Furthermore, Encom Wireless Data 
Solutions Inc. assumes no liability resulting from
any omissions in this document, or out of the
application or use of the device described herein. 
Encom’ products are appropriate for home, office, or
industrial use, but are not authorized for utilization in 
applications where failure could result in damage to
property or human injury or loss of life. 
The electronic equipment described in this manual
generates, uses, and radiates radio frequency energy.
Operation of this equipment in a residential area may 
cause radio interference, in which case the user, at
his own expense, will be required to take whatever
measures necessary to correct the interference. 

FCC Declaration of Conformity 
This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received including
interference that may cause undesired operation. 
 

Encom Wireless Data Solutions Inc., products are warranted 
against all failures which occur as a result of defective material
or workmanship within 24 months of purchase by the user.
This warranty does not extend to products that, in the opinion
of Encom Wireless Data Solutions Inc.., have been subject to 
misuse, accidents, lightning strikes, improper installation or
application, nor shall it extend to units which have, in Encom
Wireless Data Solutions Inc.’s opinion, been opened, tampered
with or repaired by an unauthorized facility. 
 

Encom Wireless Data Solutions Inc 
#7-640 42

nd

 Ave. N.E. 

Calgary, Alberta  T2E 7J9 
Phone: (403) 230-1122Fax: (403) 276-9575

 

http://www.encomwireless.com/

 

All Rights Reserved. 

COMMPAK

, 

ControlPAK

 are registered 

trademarks of Encom Wireless Data Solutions Inc.  Microsoft and Windows are 
registered trademarks of Microsoft Corporation.    All other products mentioned 
in this document are trademarks or registered trademarks of their respective 
holders. 
Revision 1.00, August 27, 2004

 

Summary of Contents for ENC-900























































Reviews:

No comments

Related manuals for ENC-900

Ramsey Electronics FR220 Instruction Manual preview
FR220
Brand: Ramsey Electronics Pages: 28
Yaesu FT-2900R Technical Supplement preview
FT-2900R
Brand: Yaesu Pages: 34
Yaesu FT-250R Technical Supplement preview
FT-250R
Brand: Yaesu Pages: 33
Yaesu FTDX101D Service Manual preview
FTDX101D
Brand: Yaesu Pages: 13
Yaesu FT-2500M Operating Manual preview
FT-2500M
Brand: Yaesu Pages: 56
Yaesu FT-2500M Instruction Manual preview
FT-2500M
Brand: Yaesu Pages: 54
Yaesu FT-209R Technical Supplement preview
FT-209R
Brand: Yaesu Pages: 39
Yaesu FT-1900R Operating Manual preview
FT-1900R
Brand: Yaesu Pages: 90
Yaesu FT-60R Quick Manual preview
FT-60R
Brand: Yaesu Pages: 22
Yaesu VR-120D Brochure & Specs preview
VR-120D
Brand: Yaesu Pages: 2
Yaesu VR-120 Brochure preview
VR-120
Brand: Yaesu Pages: 2
Yaesu FT-450 Brochure & Specs preview
FT-450
Brand: Yaesu Pages: 2
Yaesu FT-101ZD User Manual preview
FT-101ZD
Brand: Yaesu Pages: 60
Yaesu FT-101ZD Service Manual preview
FT-101ZD
Brand: Yaesu Pages: 193
Yaesu FT DX 1200 Operation Manual preview
FT DX 1200
Brand: Yaesu Pages: 140
Yaesu VR-500 Operating Manual preview
VR-500
Brand: Yaesu Pages: 47
Yaesu FL-101 Manual preview
FL-101
Brand: Yaesu Pages: 30
Vaisala HMD60 Series Quick Manual preview
HMD60 Series
Brand: Vaisala Pages: 154

Brands by name

Popular brands

Load more brands