background image

ii 

The radiated output power of this Wireless LAN device is far below the FCC radio 
frequency exposure limits. Nevertheless, this device shall be used in such a manner 
that the potential for human contact during normal operation is minimized. 
When nearby persons has to be kept to ensure RF exposure compliance, in order to 
comply with RF exposure limits established in the ANSI C95.1 standards, the 
distance between the antennas and the user should not be less than 20 cm. 

FCC Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. 
This equipment generates, uses, and can radiate radio frequency energy. If not 
installed and used in accordance with the instructions, it may cause harmful 
interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try and correct the interference by one or more of the following 
measures: 
1. Reorient or relocate the receiving antenna. 
2. Increase the distance between the equipment and the receiver. 
3. Connect the equipment to an outlet on a circuit different from that to which the 
receiver is connected. 
4. Consult the dealer or an experienced radio/TV technician for help. 

Export restrictions 

This product or software contains encryption code that may not be exported or 
transferred from the US of Canada without an approved US Department of 
Commerce export license. 

Safety Information 

Your device contains a low power transmitter. When device is transmitted it sends 
out radio frequency (RF) signal. 
CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this 
equipment should be installed and operated with minimum distance 20cm between 
the radiator and your body. Use on the supplied antenna. Unauthorized antenna, 
modification, or attachments could damage the transmitter and may violate FCC 
regulations. 

Summary of Contents for ENLWI-SG

















Reviews: