background image

Magical Balancer 

  3

 

Product Description 

 

 

19 

3-2-2

 

  Names and functions of the control panel section of the grip 

box and the bottom of the control box of the main equipment 

  The  following  are  the  names  and  functions  of  the  control  panel  section  of  the  grip  box  and  the 
bottom of the control box of the main equipment. 
(The numbers in the figure below are intended to help explain the names. Please note that they 
are different from the numbers in the Parts List.) 
 

 

 

 

No. 

Name 

Function 

Power switch 

Used to start up and shut down the Magical Balancer. 

Grip lamp 

Turns ON in green during the grip control. 

Work lamp 

Turns ON in blue during the workpiece control. 

Alarm lamp 

Turns ON in red when an abnormality has occurred. 

LCD display 

The  statuses  of  the  equipment,  any  errors  that  are  occurring,  etc.  are 
displayed. 

[Mode] key 

Used to select the display mode shown on the LCD indicator. 

[Set] key 

Used to confirm the displayed content or configure the settings. 

[Shift] key 

Used in combination with the [Set], [

], and [▼] keys. 

[

] key 

Used to increase the displayed numerical value (+1) or shift the displayed 

content upward. 

10 

[▼] key 

Used to decrease the displayed numerical value (-1) or shift the displayed 
content downward. 

11 

Function button 

Pressing  down  this  button  during  the  workpiece  control  disables  the 
balancing  mode  and  maintains  the  position  of  the  suspended  load  even 

when the load fluctuates. However, this function cannot be used when the 

load fluctuation occurs instantaneously. 
The functions of this buttons can be changed by parameter settings. 

12 

Emergency       
stop button 

Pressing  down  this  button  stops  the  Magical  Balancer  by  shutting  off  the 

air inside. In addition, the grip control mode as well as the balancing mode 

are disabled. 

13 

Status lamp 

Turns ON while the equipment is operable, and blinks when an abnormality 

has occurred. 

14 

Control box buzzer 

Sounds when the mode is switched to the balancing mode. 

15 

Emergency  release 

button 

If the balancer become inoperable, for example, when a power failure has 

occurred,  pressing  this  button  evacuates  the  air  inside  the  cylinder, 
allowing the suspended workpiece to slowly descend and be released. 

Summary of Contents for EDB-130

















































Reviews: