background image

© 2010-2021 – Endorphin.es®

YOU WILL BE DEAD – DARKWAVES NEW EFFECTS BANK:

EFFECT

PRIMARY  
‘CABIN FEVER’ ACTION

SECONDARY  
‘CABIN FEVER’ ACTION

TAP BUTTON 

1

GATED REVERB

Decay of the reverb

Noise gate threshold, by default 
set to 20%

Long hold: entering secondary 
function 

2

SPRING

Decay of the reverb

Decay of spring excitement from 
TAP button or incoming by CV IN 
clock, by default set to maximum

Short press: spring excitement. 
Long hold: entering secondary 
function 

3

REVERSED  
REVERB 

Reverb's decay value

Damping volume of the tail  
(in our case 'tail' = 'head'  
as the tail is reversed)

Long hold: entering secondary 
function

4

FLANGER 

Range of LFO

Feedback amount, by default set 
to 100%

Long hold: entering secondary 
function

5

RING-MODULATOR Modulator’s frequency 

rate

Feedback amount, by default set 
to 50%

Long hold: entering secondary 
function

6

OVERDRIVE

Tone control

None

Overdrive bypass on/off (latch)

7

COMPRESSOR

Ratio from 1:1 to 1:25

Attack of compressor from 1 to 
100ms

Long hold: entering secondary 
function

8

FREEZER

Granule size (bipolar)

none

Short/long momentary press: 
freezing enable

Summary of Contents for Queen of Pentacles












Reviews: