Rev B 2022/03
75
CyBio Well vario
Operation
Fig. 84:
A1 well target positions for 96/384/1536 well microplate
1 A1 well target position for 96 well microplate
2 A1 well target position for 384 well microplate
3 A1 well target position for 1536 well microplate
The diagram view illustrates that the tips will come down onto the edge of wells in the case
of a faulty plate type setting.
Example:
If a 1536 well microplate were to be processed with a 96 tip magazine, the tip would come
down in point 1 of figure 56.
Solution:
Set 1536 for plate type in
[Configuration]
=>
[Wells]
menu. Perform manual motion to
A1 well position for 1536 well microplates before dispensing (point 3 in figure 56).
XY
This menu item is intended for storing internal XY correction values for lifter motion. In the
event of necessary lifter replacement (according to manufacturer specification provided on
lifter underside), you can update your lifter settings here.
Fig. 85:
Display – XY correction values
The first entries in a line indicate the direction. The coordinates for zero point (nn) corre-
spond to those of a 96 well microplate.
The path, however, represents the distance to a 384 well or 1536 well in the correspond-
ing coordinate direction (refer to details on underside of lifter).
On selection of a coordinate, the lifter moves to the assigned position and can thus be eas-
ily inspected for correct adjustment. A microplate of transparent material is recommended
for lifter adjustment.
Piston speed
Piston speed (pumping rate) is a selectable parameter. This setting will only be effective in
manual mode, since programs running in PC-controlled mode include their own previously
stored pump speed values. A rotation speed of 300 rpm corresponds to an approximate
dispensing rate of 123
μ
l/s achieved with a 250
μ
L capacity pipetting head or a 12.3
μ
L/s
rate achieved with a 25
μ
l pipetting head.
You can enter an end value for motion speed here. Software settings can be made for end
speed, or starting speed and end speed or for the motion characteristic.
Stage speed
A stage speed setting will be valid for lifter motion, carriage motion and rotary stage
motion. You can enter an end value for motion speed here. Software settings can be made
for end speed, or starting speed and end speed or for the motion characteristic.
1
2
3
Summary of Contents for Analytik Jena CyBio Well vario
