background image

Technical data

Levelflex M FMP43 with PROFIBUS PA

94

Hauser

10

Technical data

10.1

Additional technical data

10.1.1

Input

Measured variable

The measured variable is the distance between the reference point (see Fig on 

ä

14) and the 

product surface.
The level is calculated subject to the empty distance entered (E, see Fig. on 

ä

102).

Alternatively, the level can be converted by means of linearization (32 points) to other variables 
(volume, mass).

10.1.2

Output

Output signal

• PROFIBUS PA

Signal on alarm

Error information can be accessed via the following interfaces:
• Local display:

– Error symbol (

ä

34)

– Plain text display

• Current output, failsafe mode can be selected (e.g. according to NAMUR recommendation 

NE 43).

• Digital interface

Linearization

The Levelflex M linearization function enables conversion of the measured value to any desired 
length or volume unit, mass or %. Linearization tables for volume calculation in cylindrical tanks are 
preprogrammed. Any other tables with up to 32 value pairs can be input manually or semi-
automatically. The creation of a linearization table with the ToF Tool or FieldCare is particularly 
convenient.

10.1.3

Performance characteristics

Reference operating 
conditions

• Temperature = +20 °C ± 5 °C
• Pressure = 1013 mbar abs. ±20 mbar
• Relative humidity (air) = 65 % ±20%
• Metallic tank, no internals, distance to tank wall > 500 mm
• Medium: water (DK > 7), respectively oil (DK = 2)
• Probe length > 500 mm

Maximum measured error

Is in Function group "basic setup" (00) starting from 

ä

58.

Resolution

• Digital: 1 mm

Reaction time

The reaction time depends on the configuration.

Shortest time:
• 2-wire electronics: 1 s

Influence of ambient 
temperature

The measurements are carried out in accordance with EN 61298-3:
• Digital output (HART, PROFIBUS PA, FOUNDATION Fieldbus):

– average T

K

: 0.6 mm/10 K, max. ±3.5 mm over the entire temperature range -40 °C to +80 °C

Summary of Contents for Levelflex M FMP43













































































































Reviews: